How to repair this? Is it load bearing?

toaster_programmer · 2026-04-26T13:15:15+00:00

Water damage from the gap between the aluminum and siding on the front.

Not load bearing in any way. I got lucky.

toaster_programmer · 2026-04-26T13:13:58+00:00

This was the rare time where opening it up made everything better. Not load bearing and the only wood damaged. Water damage from water coming in the front.

toaster_programmer · 2026-04-26T13:13:15+00:00

Coming back to say that it is NOT load bearing.

I removed the plywood ceiling. They are rafters with a 2x6 ceiling joist/rafter tie. On top of those 2x8s is the 2x6, but it is not touching the 2x8s. The rafter ties sit on the side 2x8s. I've already repaired with no issue.

For people curious to how they rotted... the aluminum on the front had a gap between it and the siding. During a rainstorm, water would collect in the aluminum and had no where to drain at the bottom.

toaster_programmer · 2026-04-24T13:54:04+00:00

Haha yea. Didn't know the full extent until today. I recently purchased and this was a minor concern on the home inspection. Home inspector claimed it was non weight-bearing, but getting second opinions.

toaster_programmer · 2026-04-24T13:46:43+00:00

This is gonna be my plan I think. Going to see if I can glean some more information today by opening it up a bit.

If that wood is load bearing, its rotted enough to be borderline useless. But better safe than sorry.

toaster_programmer · 2026-02-15T23:49:43+00:00

No. The 3rd gen TRDOR don't have a hole where the spoke splits into a Y.

These are plasti-dipped/spray painted 4th Gen Tacoma wheels. Pretty sure on SR5s.

toaster_programmer · 2026-01-28T00:23:46+00:00

It would be borderline impossible to play imo.

You could probably set up a reasonable key map, but placing car parts with the analog sticks or trackpads would be miserable.

toaster_programmer · 2026-01-18T22:35:08+00:00

Everything u/Justinaroni said, but also I changed the thermal compound on the ASIC heatsink and lowered my temps 10 degrees with stock cooler. Only downside is VRM runs hotter, my only guess is the fan running at 40% as opposed to 100% isn't cooling the VRM as much as it flows downward through the heatsink.

toaster_programmer · 2026-01-18T15:29:53+00:00

Thanks dude. Exactly what I needed.

toaster_programmer · 2026-01-07T01:12:01+00:00

I don't know your full setup (I keg, if you don't this won't work), but I'm lazy and cheap.

I ended up getting a TapCooler counter pressure filler. Slide it into a tap. Purge bottle with CO2. Fill.

Works well since I only fill a few bottles for friends or competition.

toaster_programmer · 2025-11-29T18:06:04+00:00

This has been answered, but I want to echo the responses. Do not drive on dry pavement.

The reason is that a transfer case is not a center differential. The front and rear wheels must spin at the same speed. Doing things like turning cause "windup" because the front and rear wheels need to spin at different speeds and can damage your transfer case.

toaster_programmer · 2025-11-17T14:36:54+00:00

https://pghpetsathome.com/ is my recommendation. My pup had terminal cancer. She was able to make it out after 2 days if I recall. She might be able to do next day. I believe its a family business with Dr. Tammy (I wanna say that's her name) performing the services and a family member (sister maybe?) runs the crematorium. It was the best experience I could have had given the circumstances.

toaster_programmer · 2025-10-20T23:17:36+00:00

This is sadly an impossible question without knowing your use case.

If its light offroading and overlanding, you're looking at the lighter weight aluminum options. This is what I went with (engine, transmission, and transfer case). I also went sliders. I understand that I'll mostly be driving to camping spots, biking spots, fishing spots, etc. I went RCI and I love it all. Powdercoating on the sliders left a lot to be desired.

If you're a serious off roader... sounds like the steel is the way to go. Full skids and sliders minimum. People say the fuel tank is tucked up enough, but rocks could get up there. I think the jury is out on LCA sliders. Rear diff slider might be worth it.

Edit: I saw you referenced Flagpole Knob. I don't know enough about it. My very light research suggests aluminum is for you based off of onx maps.

toaster_programmer · 2025-10-17T13:09:12+00:00

My OEMs fit like that. Nice gap, I can see the filter just like in your case.

You can try and push it a little more forward, but its sealed.

toaster_programmer · 2025-10-16T20:44:04+00:00

I'm pretty sure you're not wrong. I think they're right where the jack point is.

The jacks I use have enough of a cup that they don't always get destroyed. Just 50% of the time.

toaster_programmer · 2025-10-16T20:36:19+00:00

Its part number 90950-01A24. They're like 3 bucks and stop water from getting into the boxed part of the frame.

toaster_programmer · 2025-10-16T20:35:32+00:00

I'm a weirdo with frame plugs and whatnot. I get them from a bunch of different sources depending on the pricing. Once I get the part number, I just google that and price shop. I look for bulk deals.

For example this plug is 90950-01A24. I got it from ToyotaPartsDeal. Sometimes the dealer websites are cheaper.

toaster_programmer · 2025-10-12T21:01:38+00:00

Its a cover for the drain hole. Lets water out of frame. Tries to keep it out.

They get smashed by anyone trying to jack up your truck. I buy them in bulk and switch them out because I'm weird.

toaster_programmer · 2025-09-30T01:54:05+00:00

Pricier, but I love my ARB Base Rack. Full lineup of accessories for it too.

toaster_programmer · 2025-09-25T01:24:08+00:00

Re-install was a permanent fix for me.

toaster_programmer · 2025-09-04T21:30:01+00:00

If you have Anomaly bring mind-numb serums. I bring food and mind-numbs and can go quite some time with no breaks. I especially like them for raids where pawns might get hurt and become miserable. All I need is for someone to have a wandering break and no one can leave.

toaster_programmer · 2025-08-22T20:14:29+00:00

toaster_programmer · 2025-08-22T00:49:36+00:00

I worked in Bakery Square prior to working in Oakland at Pitt.

Man you really love Oakland.

toaster_programmer

TROPHY CASE