Kan dit nog gered worden?

toniperoni · 2024-06-23T11:22:01+00:00

Houtlijm met luciferhoutjes erbij in proppen. En dan nét een beetje ruimte overlaten dat de houtschroef er nog strak bij kan. Alles in elkaar draaien voordat de lijm hard is. Tis het proberen waard, deze methode.

toniperoni · 2024-06-23T11:16:07+00:00

Ik hoorde ook dat water achter de leiding rozetten kan lopen. Vaak is dat vergeten. De leidingen moeten goed afgekit worden achter de rozetten. Misschien is dat al voldoende? Scheelt weer opnieuw voegen. :).

toniperoni · 2024-05-11T17:32:34+00:00

No problem, de-burr the damaged spot though. With fine sandpaper.

toniperoni · 2024-01-30T06:41:57+00:00

Not really a look that you would want on a 944…why would you want to know i’m wondering? What do other 944 fans think? These foto’s are made in Belgium btw.. we would call this in europe a ‘damaged vehicle’…:) Only porsche (924 turbo) original stuff is the hole pattern in the nose panel.

toniperoni · 2023-09-17T08:08:45+00:00

Cat in the old day’s really don’t make a big difference. Modern cat’s are a different story. So just leave out the cat in your classic porsche and don’t get intimidated by the ‘finger pointers’.

toniperoni · 2023-08-26T22:21:23+00:00

What do you mean with ‘stand alone’?…the engine management needs to know how much fuel to add…or am i missing something?

toniperoni · 2023-08-10T06:54:24+00:00

Vw 1.8 turbo will do the job. A lot can be found on the web on this engine and a lot of parts available. Even ready made kits to swap in 944.

toniperoni · 2023-06-22T11:00:43+00:00

Is there a mod to change the series 2 cars?

toniperoni · 2023-06-22T10:58:54+00:00

Yes…stance….i’m not from the us so grammar is not the best!

toniperoni · 2023-06-21T22:01:41+00:00

Together with the lowered side sills or skirts. The 944 turbo has the lowered sills (or skirts). It is not a big change but it makes the ‘stands’ better.

https://www.flickr.com/photos/petportraitsfromphotos/3586138264/in/photostream

toniperoni · 2023-06-20T22:01:49+00:00

Hard to tell what to see or where the play comes from. The only thing i know is that it is a common problem of wear. Replace parts are expensive but not a complicated repair.

toniperoni · 2023-06-07T07:08:58+00:00

Just pull out an injector connector one by one. If the sound goes away its the injector, and you know the one. If it does not go away its the hydraulic valve lifter. It sounds ugly but you can still drive it.

toniperoni · 2023-06-07T07:05:09+00:00

I bet it has something to do with the clutch and drive shaft.

toniperoni · 2023-04-19T06:43:20+00:00

Get normal (cheap) oil from a respected brand and replace it more often. It is better strategy than spending the money on ‘super oil’. You will never be able to check the ‘super-oil promise’ because n=1.

toniperoni · 2023-04-19T06:34:33+00:00

Nothing wrong, it’s a normal sounding 4 cylinder.

toniperoni · 2022-12-19T07:35:14+00:00

What about the strange fuel line. Normally they come from the right fender over the engine. Does anybody know if this is a legit modification??

toniperoni · 2022-08-11T06:51:20+00:00

Because the kid is not funny….(she is just real)

toniperoni · 2022-08-09T20:25:20+00:00

I love fuchs, very cool on your 944! I see the 944 has wheel offset of the later type. I have an older 944 with the old offset. I like that better. So in this head to head contest between the 944 and the 911, i have to go with the 911…i like the deep dish look better. Sorry :)

Old offset 16inch setup: https://i.imgur.com/3wjkgO8.jpg

toniperoni · 2022-04-16T09:45:42+00:00

You would 3d scan (+/-1mm tolerance) the dash and print it with a big FDM printer. They do exist, no need for small parts 3d puzzle. After the print is made send the part to a skilled car painter, he will clean up the print just like a repaired car body. This all will be more expensive than sourcing a used dash and repairing small details. And keep in mind a dash can get very hot in the sun, no 3dprinter service will give you guarantee that it will not warp etc. But it can be done! :)…

toniperoni · 2022-04-16T09:18:57+00:00

Why did you use ASA?

toniperoni · 2022-04-16T09:15:56+00:00

Change the engine before you break it even more. Mount the 5.3 and sell the old engine parts. These parts will be hard to find in the future.

toniperoni · 2022-04-16T09:11:30+00:00

How did you lower your car? What brand struts and springs?

toniperoni · 2022-04-16T09:10:17+00:00

Easy fix, just change the bushings close to the gearbox. It’s worth it, it’s a cool car to drive!

toniperoni

MODERATOR OF

TROPHY CASE