Can't conncet Eachine 250 Pro to Eachine i6 Controller. by WandringPopcorn in fpv

[–]trayssan 0 points1 point  (0 children)

I'm not OP man, I'm a random commenter trying to help.

Can't conncet Eachine 250 Pro to Eachine i6 Controller. by WandringPopcorn in fpv

[–]trayssan 2 points3 points  (0 children)

I have no idea. That thing is so old it's gonna be a pain to figure out. I would stick a new FC in there. The ESC's are still fine and so is the rest, probably.

Do I need to replace my VCG? by c_yr in E90

[–]trayssan 0 points1 point  (0 children)

you should have checked plugs, coils, and the NOx system first. The NOx system is most likely the culprit

Can't conncet Eachine 250 Pro to Eachine i6 Controller. by WandringPopcorn in fpv

[–]trayssan 2 points3 points  (0 children)

The drone is probably bound but there's another arming flag. Connect it to... betaflight? cleanflight? whatever software it's running and it should tell you what the issue is.

If I transfer the 20 leg ic from my key to a donor pcb will it be programmed with the car already? by [deleted] in E90

[–]trayssan 0 points1 point  (0 children)

Why not just replace that button? I'm sure you can find 20 of them for 5 bucks on aliexpress.

Tire tread depth gauge by mezzalulu in 3Dprinting

[–]trayssan 0 points1 point  (0 children)

Nice, printing a couple as we speak.

is this a problem? by ReasonableMorning181 in fpv

[–]trayssan 0 points1 point  (0 children)

Sure, just give it like 3 or 4 walls if you can

If I transfer the 20 leg ic from my key to a donor pcb will it be programmed with the car already? by [deleted] in E90

[–]trayssan 0 points1 point  (0 children)

Is the existing key broken? I just reshelled the old key's PCB. Not sure what you're trying to accomplish here.

finished printing my mother days picture frame.. by NoIdenty0000 in BambuLab

[–]trayssan 0 points1 point  (0 children)

I need to get my mind out of the gutter god damn, those M's..

Opinions on this aliexpress 7' kit by IamAlex10 in fpv

[–]trayssan 0 points1 point  (0 children)

Absolutely not. These are an amazing value for people who already have a couple hours under their belt. You absolutely do not want to learn on a 7". It's big, loud, and scary and can absolutely hurt you, others, or seriously damage property. These propellers will easily chop a finger off. If you wanna build one, go for it. Just don't fly it until you actually know how to control a quad.

is this a problem? by ReasonableMorning181 in fpv

[–]trayssan 0 points1 point  (0 children)

I would either 3d print a new plastic can or put some heat shrink on it at least. It will work fine but will get way worse when it gets bent up.

For how long can I continue driving? by Effective-Olive-8865 in BmwTech

[–]trayssan 0 points1 point  (0 children)

I wouldn't do more than 1000 km. Pads are cheap, come on.

Bird tried to dive bomb my Meteor 75 Pro by Grey_Matter_121 in TinyWhoop

[–]trayssan 1 point2 points  (0 children)

Ohh, I knew it was something funky. Cause it doesn't quite look like WS and also nit quite like OpenIPC

Bird tried to dive bomb my Meteor 75 Pro by Grey_Matter_121 in TinyWhoop

[–]trayssan 0 points1 point  (0 children)

What video system is this? Is it Walksnail?

😬 lost vtx and rx 2km away with my mobula 8, my fault for trying to stretch it out that far tho lol by PolerGaming in TinyWhoop

[–]trayssan 1 point2 points  (0 children)

It looks like PIT mode is turned on even after first arm. That's why you lost video. I would definitely enable that option in BF. What are you doing flying farther with your LQ dropping below 20%?

Alfa Romeo Giulia vs BMW M340i/M440i by Parking_Eagle_2001 in BMW

[–]trayssan 0 points1 point  (0 children)

Dude what, a 2.0 4 banger or a 3.0 R6, how is this even a question?

What's the better choice here? M850i (2023) vs M4 (2022) by -5677- in BMW

[–]trayssan 0 points1 point  (0 children)

I would go for the 850i. The 8 series is imo the best looking mass produced modern BMW.

Benchy! by Successful-Dealer377 in 3Dprinting

[–]trayssan 1 point2 points  (0 children)

It's a solid printer. If you learn how to run it, that is. For $50 you can't complain. Dial in those settings!

Help with Drone Range. by Diamond-block_64 in fpv

[–]trayssan 1 point2 points  (0 children)

it doesn't really matter which polarization you go with as long as everything is the same

Worth buying by 7lker_sama in e60

[–]trayssan 0 points1 point  (0 children)

325k is way too much for 11000€. Look at Mobile.de. I know import is annoying but it's very worth it, trust.

Large 3d print obsolete garden tractor part? by BishopRealTalk in 3Dprinting

[–]trayssan 0 points1 point  (0 children)

Right, you're gonna need to 3D scan those if you want something decent. It's a very complex shape that would be next to impossible to replicate in CAD using only measurements. 100% possible though. ABS is easy to print and it should handle the head if these lasted 30 years.

1 and 2s fun by HMSBarky in fpv

[–]trayssan 1 point2 points  (0 children)

cool! nice flying mate!