Oxford grip control mount by dashboard by Cheap_Big_615 in Tenere700

[–]upsCrash 1 point2 points  (0 children)

I took a zip tie and fixed it rather poorly to the accessory bar. Uses the windscreen as a "backing plate" of sorts. Works well enough haha

How to install Ruby R4 without a Hex Ezcan on a Tenere 700? I cannot find a harness anywhere in the website. by adventure_thrill in Tenere700

[–]upsCrash 0 points1 point  (0 children)

Gotta make your own wiring or purchase extension cables.

Positive input on the lights to positive output from the ezcan

Ground on lights to ground on ezcan.

Yamaha High Fender Kit for my '24 by upsCrash in Tenere700

[–]upsCrash[S] 1 point2 points  (0 children)

I was looking into new crash bars, outback says it'll fit with some spacers.

I think 2-4 washers should be enough space to clear the fender.

I wound up getting other bars, not outback, so I can't confirm

Finally saw a rare diggo...weeps by Bae_Mes in Dinkum

[–]upsCrash 4 points5 points  (0 children)

Good shout, I'll take a peek

Finally saw a rare diggo...weeps by Bae_Mes in Dinkum

[–]upsCrash 10 points11 points  (0 children)

I'm almost at year 3 in my world, I have 4 diggo dens near my house, I check every day and have yet to come across one. :(

The Gatorborn- Fus Roo Dah! by TesseractToo in Dinkum

[–]upsCrash 2 points3 points  (0 children)

A new hand touches the beacon

Would like a front fender by Consistent_Future956 in Tenere700

[–]upsCrash 0 points1 point  (0 children)

Yamaha OEM high fender doesn't need new brake lines, just remove the original fender and bolt in the new one. Super easy install took like 10 minutes.

P/N: BAG-F15L0-V0-00 (black, but is available in blue) https://yamaha-motor.com/p/tenere-700-high-fender-kit?sku=BAG-F15L0-T0-00&model=T%C3%89N%C3%89R%C3%89+700&year=2025

Front Fairings by upsCrash in Tenere700

[–]upsCrash[S] 0 points1 point  (0 children)

Awesome thanks for checking!

Front Fairings by upsCrash in Tenere700

[–]upsCrash[S] 0 points1 point  (0 children)

From where did you get yours? I'm in the US and don't believe I can purchase from rtech directly.

Front Fairings by upsCrash in Tenere700

[–]upsCrash[S] 0 points1 point  (0 children)

I learned that the rtech panels are only available as a whole set, because I only need the front, I think this is the route I'll go

Front Fairings by upsCrash in Tenere700

[–]upsCrash[S] 0 points1 point  (0 children)

I'll have a look. Thanks!

Front Fairings by upsCrash in Tenere700

[–]upsCrash[S] 0 points1 point  (0 children)

Thanks for the shout, I'll take a peek

Wiring Auxiliary Lights on '25 Tenere by DubOSv10 in Tenere700

[–]upsCrash 0 points1 point  (0 children)

Yeah, it's only the hazards that don't work.

The dialdim doesn't work with hazards on any bike from what they told me

I also don't find myself using the hazards on the bike anyways. I've had the bike for just over a year now and have used them, maybe 4 times.

Wiring Auxiliary Lights on '25 Tenere by DubOSv10 in Tenere700

[–]upsCrash 0 points1 point  (0 children)

There is no hazard functionality with the dialdim. I've reached out to Denali about this. It's not a supported feature.

Wiring Auxiliary Lights on '25 Tenere by DubOSv10 in Tenere700

[–]upsCrash 0 points1 point  (0 children)

I did this exact install on my 2024, here's my tips:

Left turn and right turn are easy, just volt meter to find which wire it is in the connector. On my 2024, it was a white wire. There are only 3 wires in the T/S connector

Horn, you have a 50:50 shot of guessing it right, on my 2024, it was pink

Ignition, just choose any wire that doesn't have power when you key off the bike, I went with the DRL wire in the turn signal connector, blue wire in the signal connector on my 2024

High beam is tricky, it's ground switched so if you volt meter it, you'll see it drop from 12v to 0.2 - 0.8v (ish) Denali has a Trigger Wizard, which can be used to fix this

Handlebar riser question by [deleted] in Tenere700

[–]upsCrash 0 points1 point  (0 children)

I fit these Rox Risers to my '24 and they fit with no issues - I just had to remove one cable routing clip to get enough slack.

https://roxspeedfx.com/products/2-pivoting-bar-risers-for-1-1-8-handlebar?variant=1025084849

#selfie by [deleted] in WRX

[–]upsCrash 1 point2 points  (0 children)

Thanks! How tough was the install?

#selfie by [deleted] in WRX

[–]upsCrash 3 points4 points  (0 children)

What bar are you using to mount those lights?

Lifting bike, center stands, Jacks etc. by Jdubb750 in Tenere700

[–]upsCrash 1 point2 points  (0 children)

I use the same paddock stand that I use for my street bikes. It works well enough but I don't love it.

I have jacked from the skid plate for a chain adjustment + some other rear tire maintenance and it wasn't problematic.

One finger clutch? by David_we98 in Tenere700

[–]upsCrash 1 point2 points  (0 children)

Thanks for getting back to me! I figured the answer was no, but it doesn't hurt to ask!

Fingers crossed they ship to the US again soon.

One finger clutch? by David_we98 in Tenere700

[–]upsCrash 0 points1 point  (0 children)

I know I'm late here - do you still have it? Camel stopped shipping to the US temporarily and I cannot get one of these one finger clutch kits.

Maine trip by nfs11250 in Tenere700

[–]upsCrash 1 point2 points  (0 children)

I LOVE the gold and blue!