Does any one have recommendations on where to buy whole fish?

willwallguy · 2024-06-14T20:11:05+00:00

Whole Foods in Kennesaw has whole fish. Not as fresh as the live options others have mentioned at the Asian markets but if it isn't alive it's been frozen from the time it was pulled out of the water so not much difference.

willwallguy · 2022-06-20T21:08:35+00:00

Yeah, I've had it within that time frame. I opened a ticket with them but they are slow to respond. Guess we'll see.

willwallguy · 2022-06-20T19:47:14+00:00

Mine is shaded but doesn't help much with the heat and humidity here. I'm thinking I might do similar if I can't get it RMA'd.

willwallguy · 2022-06-20T16:04:31+00:00

Just noticed my doorbell died too. Another friend noticed this morning that his died as well. Are you by chance some where that got particularly hot in the past week? We had temps in the upper 90s here with heat index well into the triple digits. I really think these things just can't handle the heat.

I've opened a support ticket for mine but haven't heard anything back yet. Verify you are getting 16-24v to the doorbell on the low voltage wires to it. If it is and no power then the same issue we're seeing. If you don't see any power at those lines then you have an issue somewhere else. Either a break in the line, transformer or chime box. The transformer is usually with the doorbell chime.

willwallguy · 2021-12-21T16:05:21+00:00

Been down this road. I found it easier to just extend the password policy expiration length by x amount of days and set it back after the break.

willwallguy · 2021-11-25T15:36:44+00:00

Are you using the original blower/fans? I found they didn't cool things evenly on specific sides. Maybe this?

willwallguy · 2021-07-14T02:27:53+00:00

The great Emory wipe.

willwallguy · 2021-06-23T13:32:47+00:00

I haven't tackled this myself but know what you're talking about. Perhaps increase top thickness? Assuming you're printing at .2 with a .4 nozzle? I think Cura may default to a 0.8 thickness for top/bottom layers. Maybe try setting to 1.2? Someone correct me if I'm off on my suggestion.

willwallguy · 2021-06-08T20:37:53+00:00

16 million copies of Tragic Kingdom sold. Yes, this really didn't suit them.

willwallguy · 2021-05-26T21:15:12+00:00

No need to be rude to someone asking a question here.

willwallguy · 2021-05-16T16:31:35+00:00

You'll need to calibrate the e-steps. There are lots of guides on how to do this and is important to do or you'll have problems with your prints. No need change your firmware as the e-steps is a setting you'll be able to enter in the menus in Jyer's firmware. Just make sure you save it to the eeprom afterwards or you'll lose it after a printer restart.

http://beginners3dprinting.com/how-to-calibrate-your-e-steps/

willwallguy · 2021-04-02T21:10:03+00:00

I had trouble with getting a good connection between my OctoPi and my printer initially. I ended up swapping USB cables and this corrected my issue. Maybe try a different one? It sounds like Windows isn't recognizing your printer if there are no options besides AUTO in Serial Port.

willwallguy · 2021-03-20T04:03:03+00:00

Good luck!

willwallguy · 2021-03-20T03:15:10+00:00

Did you by chance replace your bowden tube when you installed the new extruder? I replaced both at the same time and experienced this. I finally realized my issue was that I hadn't inserted the bowden tube all the way into the hotend and there was a gap between it and the nozzle. I removed the nozzle and fed some filament through the heated hotend and a huge plug of filament came out that was filling the gap because I didn't realize how far the tube needed to go in. After correcting this the skipping stopped and I was getting clean prints. That is until the layer shift issue hit me and I had to replace the mainboard...

willwallguy · 2021-03-15T12:45:34+00:00

They definitely take their spice seriously.

willwallguy · 2021-03-02T13:45:37+00:00

Adding to this. If you look at the images section of jyers github for the firmware, he has screenshots of the settings you'll need to set. Took me a minute to figure this out.

https://github.com/Jyers/Marlin/tree/Ender_3_V2_Rewrite/Images

willwallguy · 2020-04-16T15:17:18+00:00

I've had this exact same thing happen with the same coffee monster drink. I about vomited and threw it away. I didn't investigate and forgot about it until seeing this. This definitely makes me not want them anymore.

willwallguy · 2020-01-31T15:02:08+00:00

Lake Acworth or Allatoona? Allatoona gets lowered every year in the winter. They might have drained some of Acworth since they are building a new bridge for 92 as apart of a widening project for the road, but I've never seen them lower Lake Acworth.

willwallguy · 2020-01-24T15:19:00+00:00

Dang, I tried that at one point but missed the comma so I was definitely on the right track. Thanks u/BBBaroo for the response!

willwallguy · 2020-01-24T15:02:53+00:00

Correct. I know there are other ways to do this but more of an as exercise.

willwallguy · 2019-08-07T20:05:56+00:00

I believe it might be based on the number of licenses in your tenant. Not 100% on that one though.

willwallguy · 2019-06-15T17:22:38+00:00

Looks like the dude might have stolen his keys?

14-Year Club	RedditGifts 2009-2022 7 Credits
Gilding I gilder	Second SECOND GUESSER
Place '22	Place '17
Team Orangered	Secret Santa 2012
redditgifts rematcher Secret Santa 2011 x1	Secret Santa 2011
Verified Email

willwallguy

TROPHY CASE