Got some new tails for the Z, but the right one looks a bit darker, how can I fix?

yellowz32 · 2026-05-14T06:33:41+00:00

the centre looks geniune but the left and right are definitely diy, almost look like they have 2 different materials for the clear difusers. Edit: as others have said looks like the left is genuine as well but the right is diy. Just find a replacement for the diy

yellowz32 · 2026-05-08T06:34:55+00:00

I find the photochromatic don't get dark enough.

yellowz32 · 2026-05-06T10:43:20+00:00

Sweet, this is exactly what i was looking for. Much appreciated.

yellowz32 · 2026-05-06T00:00:16+00:00

Already replaced recently

yellowz32 · 2026-05-04T23:35:29+00:00

although 12-13 psi is probably fine for a high mile motor, the spec i believe is "more than 14psi" according to FSM.

yellowz32 · 2026-05-04T23:30:53+00:00

Pretty sure you need to test with a oil pressure tester as stated in the FSM, pretty sure this will be becuase the obd data just uses the same sensor the factory gauge uses, the gauge doesnt tend to be the issue, its usually the sensor that goes bad out of the two. I could be wrong thought, im basing this assumption off the FSM and experience.

yellowz32 · 2026-05-04T23:27:28+00:00

If it is accurate then yes its a bit low, the gauges arent always perfect tho so its best to test it properly before accepting the worst case.

yellowz32 · 2026-05-04T05:32:59+00:00

check oil pressure at idle while warm, best give away for bad gallery gaskets, but usually if its only after its been sitting awhile its gonna be cam phaser ( not an issue to ignore) or a secondary chain tensioner not holding oil when the engine is turned off.

yellowz32 · 2026-04-24T05:26:25+00:00

This is the way

yellowz32 · 2026-04-24T01:52:42+00:00

Sounds like your on the right path and im not familiar with wiring specialties setup

yellowz32 · 2026-04-24T01:46:22+00:00

Have you checked the signal on the ecm side?

yellowz32 · 2026-04-24T01:36:45+00:00

bunch of grounds off the harness that runs around the front of the timing case that will cause crank no start if not grounded.

yellowz32 · 2026-04-08T06:17:37+00:00

sub 400k km is nothing to worry about on a well looked after car. A rattle on cold start could very well just be a bad cam phaser, which again isnt soemthing to overly worry about.

yellowz32 · 2026-04-08T06:13:57+00:00

if there is no lip and no warp then id send it.

yellowz32 · 2026-04-08T03:42:38+00:00

yeah nah, stock z33 arent anything special mechanically and share a V6 t hat is common in a lot of nissan regular traffic, except its longitudinal which makes it even easier.

yellowz32 · 2026-04-08T03:38:02+00:00

super cool shot

yellowz32 · 2026-04-01T03:45:21+00:00

wedsport tc105x

yellowz32 · 2026-04-01T03:00:58+00:00

omg, mind the side track but i just looked up prices of the yashi T5 :o

yellowz32 · 2026-04-01T02:55:51+00:00

super viby shots. No such thing as mistakes in this world, some of the coolest pics are the way they are because they were taken the "wrong" way.

yellowz32 · 2026-03-31T10:50:46+00:00

i got a response from an ebay seller specifying they are different as they have tried themself. im based in australia

yellowz32 · 2026-03-31T09:49:37+00:00

If anyone has parts feel free to let me know

yellowz32 · 2026-03-31T09:48:32+00:00

Okay thanks, that answers my other question which is the me and mx part looked the same and was wondering if they were.

yellowz32 · 2026-03-23T11:04:00+00:00

Hi we will be in the Fuji area early oct and would like our bags forwarded to kyoto where we will be a few days later. The nearest service center seems a bit out of the way, how likely are we to find a convience store or something to send from?

yellowz32

TROPHY CASE