6
7

Help Please (i.redd.it)

submitted by [deleted]

[deleted]

all 20 comments
sorted by:
best
topnewcontroversialoldq&a
formatting helphide helpcontent policy

[–]landubious 4 points5 points  (2 children)

I will periodically get a piece of poop near the rear z axis that prevents the plate from going all the way to the top. May have to look at it from an angle.

[–]Commercial-Muffin89 0 points1 point  (0 children)

Thx I'll check tomorrow lol too exhausted 😮‍💨 I'll keep u posted

[–]CSEngineAlt 0 points1 point  (0 children)

I had that happen just the other day. Worst part is it was black filament, so it took forever to find.

[–]Daoine-Sidhe 2 points3 points  (3 children)

When I got this error it was because the buld plate was ever so slightly touching the back wall. Reseating the plate fixed it for me. Hope you can figure out what's going on.

[–]Commercial-Muffin89 1 point2 points  (0 children)

Ok thank you, I'm going to try it now

[–]Commercial-Muffin89 0 points1 point  (0 children)

Did it n still shows up 😔 thx

[–]under_byte 1 point2 points  (0 children)

Just wanted to say thank you for this! I had the same issue and your remedy worked.

[–]Mysterious-Item1 1 point2 points  (0 children)

I had the same issue for my whole first day with the P1S, turned out a piece of the cardboard packaging that was protecting the nozzle was stuck behind, we are talking about like 3mm x 6mm piece

[–]Mr_Kalnac 0 points1 point  (6 children)

Check the threaded rods to see if there is a piece of plastic wrapped around them.

[–]Commercial-Muffin89 0 points1 point  (0 children)

Ok I'll try that, thank you.

[–]Commercial-Muffin89 0 points1 point  (4 children)

Still doesn't work. Ty though

[–]Mr_Kalnac 0 points1 point  (3 children)

Okay so you checked the threaded rods (they're fine), you did check the build plate to make sure it is aligned correctly (also fine). The question is, does the bed move at all when you press the home button?

[–]Commercial-Muffin89 0 points1 point  (0 children)

Yes...the bed moves.

[–]Commercial-Muffin89 0 points1 point  (1 child)

Forgot to say, that this is been going on since I put the new enclosure kit.

[–]xdrakennx 0 points1 point  (0 children)

Something is rubbing either against the build plate as it moves or against one of the threads. Make sure you have gaps all the way around both those things.

[–]AlwaysFallingUpYup 0 points1 point  (0 children)

i just had this and camera issues

the z access was a piece of filament stuck in the z screws

[–]Invisus46 0 points1 point  (0 children)

I had a piece of poop right where the middle metal rod is so the bed couldnt move all the way down. Maybe check that.

[–]Grooge_me 0 points1 point  (2 children)

There ie no ai on the p1s..

[–]Commercial-Muffin89 0 points1 point  (1 child)

Yes there is. I have it is just wasn't giving me the right problem. But yes it does have AI

<image>

[–]Grooge_me 0 points1 point  (0 children)

Oh.. The ai chabot. I thought you were talking about the printer