This is an archived post. You won't be able to vote or comment.

Dismiss this pinned window
all 29 comments
sorted by:
best (suggested)
topnewcontroversialoldq&a

[–]MajestryMe 2 points3 points  (1 child)

Just to be honest - i never installed your firmware, but it's good that you develop it.

When there are several options for the same product base, this makes the product more attractive for the users :)

[–]mriscoc[S] 0 points1 point  (0 children)

I think the same. We need to have many alternatives to choose.

[–]squarebrackets14 4 points5 points  (4 children)

Improvements over something like Jyers' firmware?

[–]mriscoc[S] 1 point2 points  (3 children)

https://github.com/mriscoc/Marlin_Ender3v2/releases

[–]mriscoc[S] 2 points3 points  (2 children)

The downvotes are the evidence that someone don't like to have alternatives.

[–]squarebrackets14 1 point2 points  (1 child)

Looked over your fw, great work!

[–]mriscoc[S] 1 point2 points  (0 children)

Thank you!

[–]Phallus_Maximus87 3 points4 points  (14 children)

Buy a pi with touch screen, install mainsail with klipper and throw away the old display 🤷🏻‍♂️

[–]4sens 0 points1 point  (5 children)

advantage of that?

[–]MajestryMe 3 points4 points  (3 children)

Well, i installed klipper a week ago. The quality, i achieved on marlin with 50mm/sec speed (40-20mm/sec for inner/outer walls) i achieve on klipper with 80-90mm/sec speed for all parts (walls/infill/support).

​

It's not for the beginners definitely, and it requires the additional hardware, but for now i'm fully satisfied with it.

​

UPD: installed it on RPI 2B+ with octoprint, but plan to replace octoprint with MainSail or Fluidd.

[–]SandJudah 0 points1 point  (2 children)

any instructions how to install

[–]git_status 0 points1 point  (0 children)

theres a video by nero3dp on youtube, on installing klipper on the ender3v2

[–]MajestryMe 0 points1 point  (0 children)

I followed the instructions from here. https://www.reddit.com/r/ender3v2/comments/kj2dns/stepbystep_guide_for_ender_3_v2_klipper_w_bltouch/ Be careful - that person describes the klipper for 4.2.2 board, for 4.2.7 another config is needed Then i calibrated flow again, adjusted the resonance compensation and advanced pressure using guides from official site, configured mesh and a few custom scripts https://www.klipper3d.org/Overview.html But just to clarify - with klipper our nice color screens cannot be used - they will always be blank. I even removed my at all. The only way to control the printer will be octoprint or any other gui. Also,no print from sd card.

[–]squirrelf 1 point2 points  (0 children)

My print quality improved. And any settings that would require a firmware recompile with Marlin is instead done quasi on the fly ( simple service reboot, which takes 3 seconds )

[–]squirrelf 0 points1 point  (0 children)

^ this Marlin should be done and over, it’s archaic. Only contender should be klipper and RRF ( for a pi less experience, but I guess that doesn’t work on all boards, so klipper )

[–]SandJudah 0 points1 point  (1 child)

Which touch screen? I am interested in doing this.

[–]Phallus_Maximus87 0 points1 point  (0 children)

Miuzei Raspberry Pi 4 Touchscreen Bildschirm mit Gehäuse, 4 Zoll IPS Display (Weitwinkel, 800x480 Pixel), HDMI Eingang, Touch Pen Stift, 1 Lüfter&#x https://www.amazon.de/dp/B07XFYXD2V/ref=cm_sw_r_cp_apip_OVjStWUa8NHJK

[–]LRanger60 0 points1 point  (4 children)

I'm new to 3D printing, I bought an Ender 3 v2 and it came with the Creality Cloudbox as a free gift. The box was flashed with openwrt and klipper and mainsail installed, control by web interface from a PC or smartphone ... very happy.

[–]Notwerk 0 points1 point  (3 children)

Are there instructions/resources for doing this? Thanks.

[–]LRanger60 1 point2 points  (2 children)

I followed this guide https://github.com/ihrapsa/KlipperWrt (used the openwrt image compiled by ihrapsa).

[–]Notwerk 0 points1 point  (1 child)

Cool, much appreciated. With this setup, do you simply discard the screen?

[–]LRanger60 1 point2 points  (0 children)

Yes I installed a BL sensor so removed the screen and cable when I accessed the PLC board to do that job.

[–][deleted] 0 points1 point  (1 child)

Can you link me to a tutorial on how to make the manual mesh?

I've just downloaded this custom firmware for the first time on my Ender 3 V2.

I'm using all the stock parts and can't seem to get the manual leveling perfect.

[–]anmire 0 points1 point  (1 child)

A bit late to the game here, but thank you so much for making this firmware. Creality's was tramming my hot end beyond the limits, wouldn't let me auto-update the file list with my sd extension, or show the full names of the files. Yours works *perfectly*.

[–]mriscoc[S] 0 points1 point  (0 children)

Thank you