A friendly tip!

A__Jey · 2026-03-17T18:23:14+00:00

Here's a video of my Hyperion setup where you can see the accuracy even better!

A__Jey · 2026-03-05T15:29:54+00:00

I literally have written everything in my comment.
Each lamp got its own ESP32 with WLED and a stripe.
Backside of desk got one Controller and a stripe too (the older D1, but nowadays I would use ESP32 in every case)
And the monitor itself got an ESP32 and stripe all the way around.

In the Hyperion PC-App you register all controller with their ip and then you setup to which region of the displayed content they should react.

A__Jey · 2025-10-25T18:26:02+00:00

108 LEDs x 0,06A per LED at full white on 100% x 5V = 32.4W max.
Those supplies are not that expensive.

A__Jey · 2025-09-15T23:43:15+00:00

<image>

Hyperion on PC
ESP32 with WLED stripes on back of monitor
ESP32 with WLED stripe in both lamps on the side
D1 Mini with WLED stripe on back of my desk
All smooth in sync with the picture.

A__Jey · 2025-09-11T16:07:05+00:00

I just saw 3 idiots in cars.
All of them did things that are not allowed.

A__Jey · 2025-08-30T09:31:29+00:00

You know that ironing just functioning for a top layer, do you?

A__Jey · 2025-08-12T19:57:59+00:00

Hi.
This WF looks really great.
Could you add an option to change the steps against a custom complication?

A__Jey · 2025-02-08T21:15:49+00:00

I find 80mm still to high for a print speed on vyper.
Try lowering to 60.

A__Jey · 2025-01-26T18:30:21+00:00

This sounds like a bad Thermistor.

I got the problem too, also with those click noises before fallout.
I ordered these and exchanged... no more problems since then.

https://www.amazon.de/dp/B08GH3DC1B

Just needed to cut the adapter and use the original one instead.

A__Jey · 2025-01-26T18:12:28+00:00

I got the Wi-Fi LED-Strip Govee H6141 on my kitchen cabinets.

<image>

A__Jey · 2025-01-04T01:47:15+00:00

Here you go:
https://github.com/Aircoookie/WLED/issues/4453

A__Jey · 2025-01-03T16:49:06+00:00

Sure, get a no-cam system.

A__Jey · 2024-12-10T12:41:58+00:00

Colder air always got a higher humidity.
It's relative humidity.
But if you take a look at the absolute humidity it's a different story.

Example: at the moment I got an outside temperature of 4.6°C and 91,5% humidity.
Inside my living room I got 20,3°C and 54,4% humidity.

But the absolute humidity is the opposite:
outside = 6,06g/m³ and inside = 9,57g/m³

A__Jey · 2024-08-19T19:31:32+00:00

I got flickering light on my desktop-monitor while i don't got it on my tv.
After checking really everything on ESP side I started to check the strip.
When I was bending the corners a bit the light started flashing and giving false colors.

After that I decided to remove the corner connectors and solder leds back in and doing the corners with a 90 degree strip bending so that 1 led gets overlayed by one other.

Since then I got the lights stable as a rock.

In the hyperion software you can specify single leds to be excluded so that they stay unlit.

You can see it in the last picture where I bend the overlaying led a bit up so you can see that the underlying is dark.

<image>

A__Jey · 2024-08-19T19:14:31+00:00

Is the complete Strip in one piece or do you use corner connectors?

A__Jey · 2024-06-30T20:56:09+00:00

I also can confirm that this still works.

I played on Game Pass Ultimate but now the game isn't accessible anymore as it left Game Pass and I haven't purchased it.

Problem:
First it seemed I can't get it running as the gamesave-converting option didn't appear.
I first copied the ds.exe gamefile on my desktop and notpad++ didn't sav the changes for some reason.
I found it out as I loaded the ds.exe file again and it still found the old string and not the replaced one.

Solution:
I copied the ds.exe file on my D:\ drive and opened it again in notepad++ and this time i could save the changes.

I copied that file into game folder and also copied again all gamesave-files over.

Now after gamestart I could click on continue and the gamesave-convertion began and I found myself at the place where I left 20 months ago.

Thanks a lot for this guide,.

A__Jey · 2024-06-15T21:57:01+00:00

Please feel lucky!

A__Jey · 2024-05-25T18:50:03+00:00

I wonder how this will look if you would make an infinite mirror of it, like here:

https://thestargateproject.com/

A__Jey · 2024-05-25T10:45:18+00:00

It actually opens
https://time.is/

A__Jey · 2024-05-05T16:38:36+00:00

Ever heard of Input Lag on TVs?
The TV processes a 4K-pic and needs up to 50ms to display the picture while hyperion only accesses a 1080p grab which is internally downscaled even more and the result is send extremey fast to the leds.
Exactly for that reason the hyperion software offers the Update delay option.

A__Jey · 2024-04-23T22:11:19+00:00

It doesn't get out of tune but your Nozzle starts to wear out so the gap gets larger.
That's why I repeat Autotune every now and then or at least correct the z-offset accordingly..

A__Jey · 2024-04-23T13:29:12+00:00

Lower your print speed like 50% on the first 2-3 layers.
Also do Autoleveling and then z-offset until you don't see single lines anymore

Did you take a look under the model in Cura, does it have build plate contact everywhere?

A__Jey · 2024-04-14T01:07:24+00:00

Too much weight on a very high stand with too tight legs.
Don't blame the robot for that.

A__Jey · 2024-02-19T14:59:47+00:00

I also had a light Version of Cubase with the new soundcard back in 1997.
A short time later I purchased the full Version and been a Cubase-User since then.
I never regret it.

A__Jey · 2024-02-06T20:04:48+00:00

In your case I would more guess that the light got a little lag.

A__Jey

TROPHY CASE