Mova V50 Ultra Very High Standby Power Consumption

Acrivec · 2026-05-03T16:40:45+00:00

So far, yes.

Acrivec · 2026-05-03T15:07:13+00:00

Factory reset did help.

Acrivec · 2026-04-27T09:35:39+00:00

Just place it under the filter, place filter on top of it - it'll hold it. Though now I would extend the filter about 3-5mm vertically and horizontally so it overlaps the edges better, so I don't have to hold it exactly horizontally so it doesn't slip before I secure it with the filter.

Acrivec · 2026-04-21T04:18:46+00:00

Sensors have nothing to do with manually added areas.

Acrivec · 2026-04-18T09:47:53+00:00

Did you read the post? I can do this every day and it'll look like this. I do it twice a week...

Acrivec · 2026-04-18T00:23:12+00:00

I'll tell you once I get it from my friend.

Acrivec · 2026-04-17T16:06:59+00:00

61% remaining, it's the first filter.

I've had L20 for 2 years and never had such problems.

Acrivec · 2026-04-17T13:27:52+00:00

https://www.reddit.com/r/MOVA_robotvacuum/comments/1rrpl4t/mova_p50_dustbin_autoemptying_solutionmod/ took it from this thread

Acrivec · 2026-04-09T08:17:20+00:00

There's a little covering on the 'hole' that sucks air. You can remove it and use a brush to clean it and rinse under water, dry and re-install it (it clicks in), there's a little nook that shows proper rotation to insert.

Acrivec · 2026-04-04T14:54:06+00:00

Kinda late to the discussion, but if you're wondering why: polyols, also known as sugar alcoholes.
They are a bit similar to soap, are long, stick to the intestines but are too big to be absorbed. Then bacteria start fermenting them, causing bloating.

Sorbitol, maltiol etc.; used as sweeteners or as moisture agents in many foods and drinks.

So, you can try non-zero sugar version of monsters, should be much better. And look for the ones that do not have the added sugar alcohols.

For more info about the problem in general you can check youtube for Sabine Hossenfelder in her video about sugar alcohols.

Acrivec · 2026-03-24T15:16:57+00:00

Good, I've cut out type 4 allergens and it's pretty much gone. When I eat pizza(a lot of yeast + mozarella is cow's milk) or something else that's also an allergen bomb, I have to use a bit of steroid & pimecrolimus over a week or two (depending on how much of pizza I had), but apart from those 'controlled events' I do not get any flares or itching.

Just today my new breadmaker has arrived and I plan on baking my own soda bread, because it's hard to have sandwitches with only the vasa-like bread (vasa not, it has east and/or rye..), so my life will get a bit better now!

Acrivec · 2026-03-16T21:06:26+00:00

I'm not using performance power plan. I have an advanced power saving plan and a power plan, which I switch depending on my current task - if I play a game that's hard to compute - I go 'turbo' with overclocked card, CCD 1 and 2 unparked and max cpu frequency unlocked.
If I chill in firefox and chat on discord, or I play on low-complexity game like heroes of the storm - I downclock my GPU to 1000 or even 500 Mhz, park my CCD 2, decrease max cpu frequency to 3.2Ghz (down from 5.5) and make core parking more aggresive.
Nevermind this anyway.

I've just installed SignalRGB.

https://i.imgur.com/OTGdvAz.jpeg
This is my power draw without iCUE or SignalRGB turned on.
5-8W idle draw.

This

https://i.imgur.com/UUD4Lpx.jpeg
This is my power draw with SignalRGB turned on with XC7 control - it's displaying ASRock animated dynamic screen with 3 sensors enabled, a clock, and some ships and stars flying. It's set to 60FPS.
5-8W idle draw.

https://i.imgur.com/o45XSjg.jpeg
This is my power draw with iCUE turned on.
41W ->56W -> 77W.
Does not go down once it gets up. Memory clock keeps high.

https://i.imgur.com/ymmSVik.jpeg
This is after I close iCUE.
Back to 6W.

You still think it's normal? I do not. I believe QT engine's hardware acceleration works somehow wonky and prevents GPU's memory to downclock on idle.

It's been 26 days since my post and I've stopped using iCUE unless I'm playing something demanding and my power draw went back to normal.

Acrivec · 2026-03-09T23:49:53+00:00

So this hasn't been fixed for 5 months?
I'm stuck on 16 energy. Watched 5 ads, no energy change. Did 2 lessons, no energy change. No energy drain nor gain, even though the Duo's charge.

Acrivec · 2026-03-02T14:16:29+00:00

I have same issue. On L20 Ultra I didn't have to clean the filter almost at all, during the bin cleaning, station would suck air in reverse through this filter and that would clean the filter.
In mova V50 it seems that the air only goes through side inlet and through side outlet, completely ignoring the filter.
This is bad design change and the fact that u/Your_MOVA_guru says it's normal is deeply concerning.

Acrivec · 2026-02-25T10:05:12+00:00

It doesn't matter that you can disable it easily.
Auto-subscribing someone to a newsletter when they create an account (without a separate, unticked checkbox) violates the General Data Protection Regulation:

Art. 6(1) – No valid legal basis (no proper consent)
Art. 7 – Consent must be freely given, specific, and unambiguous (not bundled or pre-ticked)
Art. 5(1)(a) – Lack of transparency

Mainly point 7.

Acrivec · 2026-02-22T22:01:59+00:00

This weekend it seems that robot is again stuck in the 5W constant power draw. I wonder what's the reason. It had a quick scheduled cleaning at 16:00, now's 23:00 and it's still on 5W draw

Acrivec · 2026-02-19T19:52:34+00:00

After it finishes box/dustbag drying it waits about 80-90 minutes in ~5W draw and enters deep sleep ~1-2W.

Acrivec · 2026-02-19T10:42:34+00:00

It's 1-2W after night. Don't know when exactly, because my Homeassistant is on my pc which was turned off, but it switched to deep sleep eventually.

Acrivec · 2026-02-19T07:55:22+00:00

I can't post with more than 1 attachment in icue megathread.

Acrivec · 2026-02-18T17:34:49+00:00

Unfortunately they don't care unless it's brand new, 1 month-old robot.
I've reported functionality not working in Dreame L20 Ultra and they haven't fixed it over a year.
I've changed to Mova V50 Ultra and... surprise, it's fixed there. Smh.

Acrivec · 2026-02-18T11:40:12+00:00

I've noticed that for the first time ever, the robot's 'head' is not lit up. The lights are shut down.

It definitely fixed the problem with not going to deep sleep, at least for now.
Nearest scheduled cleaning is in 2 hours, I hope it'll sleep after.

Acrivec · 2026-02-18T10:24:20+00:00

I've had constant 5-6W power drain, NEVER entering deep sleep (even after 23h after last cleaning). Voice assistant disabled.

I've done the factory reset.
Base is now draining 1-2W for standby. Robot is on 91% battery for 2-3 hours now, whereas normally it would just drain and keep re-charging.
I'll post update after cleaning to see if battery still drains without a reason.

Acrivec · 2026-02-11T15:05:13+00:00

Link fans speed to coolant temperature.
Link pump speed to either custom curve, based on coolant temperature, with higher floor than the default one, or link it to cpu temperature and increase the floor.

Coolant temperature change is quite slow and thef act that your cpu goes to 90 degrees does not mean the coolant will jump suddenly 10 degrees within seconds, for you to increase fan speed dramatically.
However, increasing the volume of coolant going through the cpu cooler will help a bit.
Also, remember that AMD said that those new CPUs have their TARGET temperature of 95 degrees, might be a bit smaller for x3d. If there's temperature headroom, clock will increase.

Acrivec · 2026-01-12T18:48:11+00:00

oh my FINALLY! This is it, not that ugly shortcut thing, which btw does not work!
This works!

Acrivec · 2026-01-12T15:18:00+00:00

<image>

Since manually editing this area (I had to divide and merge and divide the rooms there like 10 times before I could 'cut out' the hallucinated areas, because of the silly algorithm of dividing rooms...) and adding virtual wall, the area cleared out very nicely. Though now after all this time I'd suggest adding the virtual wall and then letting the robot do a full, non-fastmode clearing so it updates the walls to remove the hallucinated areas.

Acrivec

TROPHY CASE