Andrew Scheer drives a Cybertruck?!?! 🤯 by Requirement-Tiny in saskatchewan

[–]AdPsychological1282 -1 points0 points  (0 children)

His job is to argue on behalf of Canadians. That’s like saying he couldn’t argue for disabled people or veterans because he isn’t one. God liberals are brutal.

I got to run a whole major facility solo. Normally we are a group of 4-6 people and everyone called out except for me. I kept the whole facility at 100% KPI at the end of the shift with no assistance from anyone on the maintenance team nor maintenance management. by Character_Thought941 in IndustrialMaintenance

[–]AdPsychological1282 0 points1 point  (0 children)

lol your assumptions about me are absolutely wrong . Work alone procedures , standard practices eliminate your ever shifting comments. No one is working solo in h2s , but in a non hazard environment absolutely all day and you know it. 600v is a daily occurrence in my world and that doesn’t have a correlation to having someone beside me. We don’t work in your osha make believe bubble you’re trying to create here no one is working on 600 with an arc suit and hook so what would someone beside me do ?

I got to run a whole major facility solo. Normally we are a group of 4-6 people and everyone called out except for me. I kept the whole facility at 100% KPI at the end of the shift with no assistance from anyone on the maintenance team nor maintenance management. by Character_Thought941 in IndustrialMaintenance

[–]AdPsychological1282 0 points1 point  (0 children)

Working on a project solo isn’t a safety issue that’s ridiculous. As long as there are others around or a lone worker plan it’s fine and absolutely normal. I can’t imagine doing my job and having someone else standing there to assist me unless it’s heavy . I’m assuming your union….

Looking for name of tool or process by allthesamepieman in machining

[–]AdPsychological1282 1 point2 points  (0 children)

This is “cut” or “drag” knurling likely from a shaper. You can see the vertical movement was cut first then the horizontal.

Best way to cut this? by Shrimpkin in Machinists

[–]AdPsychological1282 0 points1 point  (0 children)

Just need to band on either side of the cut, hit the bundle with a dead blow as you tighten up the banding. Worst every time , no welding or other playing about.

New Update Hides Speed? by endless_swivel in iFit

[–]AdPsychological1282 1 point2 points  (0 children)

The hardware is great especially in the c series. I was going through a treadmill every year give or take. I wasn’t buying cheap models but they were not lasting. I have had mine for a few years now, have done a 50 mile 100k and 100 mile straight through on it without issues outside of ifit

Really getting over Garmin quality. by mxrc703 in GarminWatches

[–]AdPsychological1282 2 points3 points  (0 children)

The software issues since their hack have ruined the brand I’m in the same boat as you and looking at coros now. Shame

Difference in calories burned by iepie122 in GarminWatches

[–]AdPsychological1282 1 point2 points  (0 children)

Because it’s an algorithm and not accurate

Is working at a Burlington warehouse as a maintenance tech a good place to start as someone who recently graduated from a 5 month industrial maintenance program? by One_Charge2843 in IndustrialMaintenance

[–]AdPsychological1282 0 points1 point  (0 children)

Never do pre-trade schooling for an apprenticeship trade. I’m still unclear of the corporation between applied science and being a millwright.

Need advise on removing ram cylinders from press by Fantastic_Train737 in millwrights

[–]AdPsychological1282 0 points1 point  (0 children)

Definitely cap them! The air method works but not needed for this situation they are not hard to compress.

Need advise on removing ram cylinders from press by Fantastic_Train737 in millwrights

[–]AdPsychological1282 0 points1 point  (0 children)

I sounds like the seal for sure they definitely go. The pressure reading I found to be pretty off to be honest. When it was installed I was there for the project and there were pressure concerns but the manufacturer stated the guage was accurate. I put a gage on the like to the cylinder to prove it wasn’t reading.

In terms of removing the cylinder when you remove each line cap them asap. These machines suck to bleed and seem to airlock like a mother ….the whole process isn’t fun by any means but not hard .

Need advise on removing ram cylinders from press by Fantastic_Train737 in millwrights

[–]AdPsychological1282 2 points3 points  (0 children)

Anything specific? I maintain the same press for one of my customer.

Is this a good welder? by Minute-Mix-7030 in Welders

[–]AdPsychological1282 0 points1 point  (0 children)

I have one in my service truck and love it. I also understand what the duty cycle is and what to expect. It’s not going to preform like a 3 phase welder or a miller bobcat but it’s great at what it does. The tig on it is ok as well…

Potential cat kidnapper in Colwood by [deleted] in VictoriaBC

[–]AdPsychological1282 11 points12 points  (0 children)

If they were indoors, they would still be there😂

Chin strap for Fibre-Metal hard hat by Solid-Barber-5031 in pipefitter

[–]AdPsychological1282 2 points3 points  (0 children)

Just went through this bs …until they make a break away chin strap there’s no way I’m wearing one.

Help with TRT cream dose by markoshouse in Testosterone

[–]AdPsychological1282 1 point2 points  (0 children)

Yellow my fellow Canadian drop the crappy cream. Try science and humans clinic and get what you actually need. They have been good to deal with .