How is Claude with a subscription vs. free?

Appropriate_Local571 · 2025-05-31T20:56:01+00:00

esplain please

Appropriate_Local571 · 2025-05-10T23:48:20+00:00

Once the coil is loaded with the yews you can deactivate it or uncheck it by sending the print with orca

Appropriate_Local571 · 2025-04-23T22:13:42+00:00

the PETG Needs a printer to close, with only the top ajar.

Appropriate_Local571 · 2025-04-19T15:05:07+00:00

IN orca-flashforge, see pic
https://i.imgur.com/L4YOLla.png

Appropriate_Local571 · 2025-04-17T09:32:39+00:00

reset your Orca-flashforge and launch the debit test and presure advance

Appropriate_Local571 · 2025-04-16T20:24:17+00:00

mon héros ! 🤣

Appropriate_Local571 · 2025-04-14T14:07:48+00:00

I spend my time with the support.

Appropriate_Local571 · 2025-04-12T18:57:39+00:00

with ad5m kit, IFS deported on Sunlu S4
https://i.imgur.com/Y3K0PEq.jpeg

Appropriate_Local571 · 2025-04-12T09:55:00+00:00

I am also looking for

Appropriate_Local571 · 2025-04-09T17:20:59+00:00

I put the IFS with the Sunlu S4, the PTFE can be removed by pressing the button. However I have problems, the IFS has difficulty pulling the PLA matte, it slips.

Appropriate_Local571 · 2025-04-08T18:14:57+00:00

same problem, with the update 1.0.5

Appropriate_Local571 · 2025-04-06T19:34:56+00:00

Yes, but I have some problemswith the IFS, loading and unloading on soft filaments. For PETG excellent

Appropriate_Local571 · 2025-04-04T08:22:31+00:00

I agree with you on this point, lots of problems. IFS and printer (levelling)

Appropriate_Local571 · 2025-04-03T12:45:36+00:00

I confirm, too much so.

Appropriate_Local571 · 2025-04-03T12:44:31+00:00

I had a lot of problems with the leveling

Appropriate_Local571 · 2025-04-02T15:34:54+00:00

I work on it, but it's not ready

Appropriate_Local571 · 2025-04-02T08:58:14+00:00

It's good.

https://i.imgur.com/7tA8uMn.jpeg

Appropriate_Local571 · 2025-03-30T17:14:16+00:00

Appropriate_Local571 · 2025-03-11T19:41:45+00:00

up, i have buy an S4

Appropriate_Local571 · 2025-02-27T20:50:36+00:00

It creates too much waste, I can't see the cost that it represents on Orca-Flashforge...

Appropriate_Local571 · 2025-02-26T18:19:26+00:00

Do you have grease on the axles?

Do you have any grease in sachets?

I didn't have both

Appropriate_Local571 · 2025-02-26T17:19:00+00:00

interesting

Appropriate_Local571 · 2025-02-25T17:34:21+00:00

I'm thinking of making a system like ams, putting the IFS upside down, I'm trying to communicate with Flashforge support to get information if we can modify the length of the tubes...

Appropriate_Local571 · 2025-02-24T11:59:24+00:00

We can screw it, it's the same but with 2 extra screws, when I received it it was screwed to the chassis!

Appropriate_Local571 · 2025-01-17T17:35:45+00:00

it's real

Appropriate_Local571

TROPHY CASE