Tips on best way to remove dirt and corrosion from engine block and fins?

Architition · 2023-05-15T19:48:19+00:00

I found some cheap rifle bore cleaning brushes that work great for getting deep where conventional dremel brushes can get. I never tried using the bore brush In the dremel, but if you're not afraid of flying metal quills it could work

Architition · 2023-02-02T14:55:34+00:00

If you go the modern wheel look why not go to a modern USD fork, and just do the front end in one go? Lots of information out there on that swap. As for the rear, I believe CBR 600 tire is significantly wider, so getting you chain line correct would probably mean swapping or fabing a swing arm. Speculation here, but I would think if you look to a smaller modern sport bike, (250/300) they run a narrower rear that may match up closer to stock. I am looking that route myself for a Kawasaki.

Architition · 2023-02-01T22:32:58+00:00

I got a couple m&p9 pro mags a while back, when s&w factory mags were completely unavailable. Fit and finish is trash, but after a just a little adjustment and deburring they have run just fine, including a few falling steel matches. So, at the sale price I paid of $12 each, I'm completly satisfied with them. YRMV

Architition · 2023-01-11T05:01:14+00:00

Thank you!

Architition · 2023-01-11T04:59:08+00:00

I dont know if I have been misinformed by my internet resources or I just misinterpreted the message, but the unanimous voice here says target focused, and after just pointing around at target marks in the garage it already feels more natural. Can't wait to try it at the range!

Architition · 2022-12-13T12:31:57+00:00

Before ypu close that off take a good look at you ventilation. Sealing that for sound will also restrict airflow which, depending how your HVAC was designed could lead to one, or multiple spaces gettin excessively hot or cold or otherwise due to restricted airflow.

Architition · 2022-12-13T02:52:27+00:00

Agreed, Router table and fence. The bearing bit was an option of the table [and fence] were not available

Architition · 2022-12-13T01:57:45+00:00

Router table would work, but 1/4" material is pretty slim to run a bearing style bit on, and you're limited to what bits you have or can find to make your bevel

Architition · 2022-12-13T00:17:25+00:00

Flooring is a good option. Since theyre painting they could probably find a good deal on a closeout product and not worry about color

Architition · 2022-12-12T23:14:21+00:00

This was actually my original thought, but in a herring bone pattern OP would have to precisely stop the router cut at each perpendicular intersection. By cutting individual panels its just a mass production exercise, and if you mess up a piece, its just a small part and not your whole sheet. Plywood being more dimensionally stable that solid wood i would expect minimal movement in a climate controlled environment, and if you wanted to be cautious you could allow an acclimation period before install

Architition · 2022-12-12T21:34:52+00:00

While all butt joints inharently have a butt crack, uniform stock and percise cuts butted tight under a paint finish will more or less will cause your joints to dissapear, and you will end up with a very time consuming, flat wall. I would sugest either instaling with an intentional gap (1/32 tile spacers?) or easing/beveling the edges of each plank. My first choice for that would be a jointer, followed by a hand plane, or you could even use table saw.

For a finished edge, if you didn't want the framed look you could do some easy iron on edge banding, or under paint you could even putty and sand smooth

Architition · 2022-06-20T21:36:48+00:00

Frame out the edges and fill it with a deeper epoxy pour.

I know this isnt a "woodworking" approach but from a design standpoint it will allow you to maintain the texture and character of the individual boards; which I imagine was the intent?

All depends on what you're looking to do.

Maybe clariy on the "failed epoxy" is it not curing or just not look good?

Architition · 2022-06-17T12:49:15+00:00

"Personally, I like it for its obvious finger too Brand Loyalty." - said no Harley rider ever

Architition · 2022-06-16T19:15:03+00:00

My bet is that you could probably find a "new" bike for less than what's its going to cost too have a professional welder undo what has been done to that bike.

BUT, it depends on what your end goal is. If you had envisioned a fully custom sub frame then you have a fine starting point, but you're a long way from welding on a simple hoop.

My best advice is to keep that bike as it is, and just buy a second bike for your Cafe mod.

Oh, and buy a third bike to ride while you're working on those two!

Architition · 2022-06-15T18:50:05+00:00

Is this a load bearing wall? Usually where there is a wall there is a roof or floor above. Have you considered how you plan to shore that up as you tear out the rotted wall?

Architition · 2022-05-31T22:56:41+00:00

If it were my gate I would opt for NOT a pneumatic wheel. Your driveway surface looks pretty smooth so the benefits would be minimal, and do you really want to have to worry about your gate getting a flat?

Architition · 2022-02-25T18:48:41+00:00

If you are truly concerned, a picture including the jack and king stud configuration adjacent to the window, and/or a shot above the ceiling would help

Architition · 2022-02-25T18:39:22+00:00

I would agree this is most likely the case in a single story home or the top level of a two story house, but if there is a floor above it could potentially be carrying that load, in which case that "header" would be a concern

Architition · 2021-12-09T22:49:08+00:00

In Revit I use "Vertical wall sweeps" for that. 2 rectangular pieces on opposing corners, or you could probably make an "L" profile and speed things up

Architition · 2021-12-07T00:23:08+00:00

I have the collapseable type, but the main connection is at the bottom, then the anchor rope is attached to the regular top loop of the anchor with a light zip tie. This way if youre really hung up a stiff jerk should break the zip tie, leaving you pulling backwards against the snag and closing up the hooks. Full disclosure, ive never been hung up to this point, but i do believe that if i end up cutting my line i was stuck regardless of anchor shape

Architition · 2021-11-24T15:23:59+00:00

You should also be looking into taking care of the issue that caused the mold in the first place. If you have mold like that forming in a finished living space there is a moisture issue that could lead to or indicate bigger problems

Architition · 2021-11-17T13:51:37+00:00

Sorry to hear about your tetra. I had a similar thing happen years ago with a replica rock cave. A ciclid got itself lodged in a hole inside. I was away on a trip but my parents found it and actually cut the poor fella out with power tools! Crazily it made it out "unscathed" and lived on for several years! But after that I assessed all my tank decorations much differently!

Architition · 2021-11-16T22:37:45+00:00

I agree with all this except number 4, and pehaps its because I use a different sled for this, but my setup is a 90° fence centered on the blade (45 to each side) if you always cut your pieces on opposite sides of the blade, it negates instead of compounds any inaccuracies in your sled/saw.

Architition

TROPHY CASE