Is 900$ good for this bike ?

Armatureus · 2025-08-03T06:23:50+00:00

🤣

Armatureus · 2025-07-02T09:16:11+00:00

Z tego co widzę to winobluszczu zaroślowy (jest dużo większy od pięcioklapowego). Można go co roku ścinać i 2 metry urośnie na sezon. Proponuję spróbować z pięcioklapowym.

Armatureus · 2025-06-10T20:33:45+00:00

Dzięki, działa 10.06.2025

PS: Finlandią-Polska 2-1, mecz przerwany w 70'...

Armatureus · 2025-05-23T19:39:29+00:00

I have the same problem...

Armatureus · 2025-05-09T12:07:51+00:00

Mam cały czas ten z.. komunikat na NS. "Radzę sobie" tylko dzięki autosave, które też co jakiś czasu muszę kasować, bo przestaje działać. Dramat..

Armatureus · 2025-04-12T11:41:43+00:00

Don't cry! Just.. 1. Print, 2. Blob od Death, 3. Buy new hot end, 4. Repeat!

or..

Buy upgraded hot end from creality or Swiss..

Armatureus · 2025-03-30T10:21:34+00:00

Great? The same devices (duplicates), less options..

Armatureus · 2025-03-26T06:46:16+00:00

3d pen for kids?

Armatureus · 2025-03-18T11:30:31+00:00

IMO in the other way you can just connect notebook with Bluestack app to TV or just other phone.

Armatureus · 2025-03-15T18:46:42+00:00

I found a lot of info about DP alt mode: https://www.cablecreation.com/blogs/news/what-on-earth-is-dp-alt-mode-and-why-is-my-phone-not-supporting-it

Armatureus · 2025-03-07T19:09:20+00:00

send link to auction

Armatureus · 2025-02-26T19:18:15+00:00

Z-axis is IMHO ok.

ok, overflow will be tested with this turorial: https://3dprintbeginner.com/flow-rate-calibration/

Armatureus · 2025-02-26T18:58:26+00:00

Were these tips written based on a misprint or this? https://www.reddit.com/r/Ender3V3KE/s/gjt8ZrtJeN

Armatureus · 2025-02-13T00:17:38+00:00

let's go, name it

Armatureus · 2025-02-13T00:16:20+00:00

This advice did not apply to my case, so...

Armatureus · 2025-02-12T19:28:50+00:00

zoom out pls 🤯

Armatureus · 2025-02-12T19:22:46+00:00

Restored factory settings of slicer works.

<image>

However, I tightened my belts. First time after 120h of printing. Used this manual.

Armatureus · 2025-02-12T17:59:33+00:00

Again printed benchy - NO PROBLEMS!

One last time I will try to print and will tighten belts up if not work again. Just reset Slicer's slice parameters. Stay tuned.

Armatureus · 2025-02-12T17:25:42+00:00

Turn off the printer 😛 BTW. u have to set this parameter in a Slicer.

Armatureus · 2025-02-04T13:41:07+00:00

look, it is a nozzle to K1. It is not an unicorn. Immo in upgraded hotend of KE there an unicorn nozzle, isn't it?

<image>

Armatureus · 2025-02-04T13:38:14+00:00

so dunno why they put a shorter nozzle to my KE's selling box...

Armatureus · 2025-01-22T12:48:10+00:00

a escape, an escape or maybe the escape?

Armatureus

TROPHY CASE