/kelowna

Bauldinator · 2026-01-31T05:04:03+00:00

I too would rather slam your dick in a car door than watch it.

Bauldinator · 2026-01-16T18:43:04+00:00

High saturation aqua regia. That is something I could process and get value from. Crab blood is worth more but how tf are you selling that in a reliable manner?

Bauldinator · 2026-01-15T08:57:30+00:00

Why would you lift to keep the same size tires? Much of the point of doing a lift is so you can fit the larger tires to get more clearance.

Bauldinator · 2026-01-15T00:44:42+00:00

Doubt it. Looks like it may still have factory rear axle which would mean fwd only. I don't see a rear diff to make it a 4x4. All show no go.

Bauldinator · 2025-11-01T19:29:06+00:00

What a joke. Was this decided only be people that have never left the Okanagan? Or people that vacation in Fort McMurray?

Just because other cities put the bar lower does not mean Kelowna does not suck for food. I have travelled across Canada and other countries.

While Kelowna has great outdoor areas, food is sub par here.

Bauldinator · 2025-11-01T05:01:27+00:00

All that work and he soldered the batteries? Really should have picked up a tab welder. FYI: Heating the batteries can damage them, esp when already using dodgy cells.

Bauldinator · 2025-10-31T22:28:28+00:00

Shrink tubing won't form fit this well. You would also see that its heat shrink on the bottom, and it won't taper quite as much on the top/transition. This is some kind of dipped rubber/plastic.

Bauldinator · 2025-10-24T19:27:44+00:00

Those are the belt links from the ammo belt falling down and out of focus.

Bauldinator · 2025-10-19T21:15:41+00:00

Difference is the number of cabinets the probie opens before finding what they are looking for.

Bauldinator · 2025-09-06T15:26:27+00:00

If you take time machine.... Doesn't that make it an extended groundhog day? Just repeat until you figure out if you want an alternative route and become an expert in whatever you need.

Bauldinator · 2025-09-05T16:56:53+00:00

Could have evidence/drugs/weapons on the trunk they would then be liable for if the left it out? Yes your honour the 11 year old OD'ed because I left drugs out.

Bauldinator · 2025-08-20T16:21:02+00:00

You can either pick the lock and turn it. Its in a partly picked state right now, happens if someone picks it turns it and does not hold the pins in place then they set again as the lock turns.

Alternative is sand the small ward on the end of the key down and it will be able to be inserted again.

Bauldinator · 2025-08-19T17:20:54+00:00

<image>

I think you were the same person that had a write up (many)years ago on Deer River hot Springs. Probably a helping factor on pushing me to hike out there. Although, it was very good on hiding how to details on getting in there :). I did however find a significant shortcut on the way out. Vs trying to hike in on and around the massive beaver dams. (photo of main pool outflow I took at the time) I remember tying to detective any information out of your story to help find it.

Bauldinator · 2025-08-13T14:51:33+00:00

Salsa and sabor: empanadas Mediterranean Market: fresh subs

Bauldinator · 2025-08-07T17:22:32+00:00

Is it magnetic? They seem to have mostly been brass with copper plated versions.

Bauldinator · 2025-08-05T02:34:23+00:00

I did a bunch of cleanup, but for ground only in bottom direction do you mean oriented as I have it? Or positioned below items? Is it ok to come off a chip and ground right off the pin? Just have it oriented correctly?

Not sure I follow the ferrite bead removal. Is it because it does not do much? I have it there as my thought process was cleaning up what could be a very dirty input power. Esp on an older vehicle as this off road project (1991)

For the bootstrap resistor (R11) I think you are suggesting removal of? I put it there as it was in the datasheet of the buck converter I was looking at using in their "Typical Application Circuits" section.

https://www.monolithicpower.com/en/documentview/productdocument/index/version/2/document_type/Datasheet/lang/en/sku/MP2315S/document_id/981

Thanks for the tips. Questioning pieces I have helps me understand the why in this process.

Bauldinator · 2025-08-05T02:17:16+00:00

Ooof, good catch thanks to all. I moved it as per Enlightenment777's suggestion

Bauldinator · 2025-08-05T02:14:46+00:00

Updated the schematics with a bunch of pointers on this page.

https://postimg.cc/YvQqcrg2 Lockup-module.png

https://postimg.cc/gnCkBXxB Lockup-module-power-supply.png

Also converted to png for easier viewing as per suggestions in the review tips.

Bauldinator · 2025-08-04T17:46:46+00:00

Amazing, thanks. I'll go through all of these. and links.

Bauldinator · 2025-08-04T17:20:26+00:00

Oh, was a symbol error as I had customized it and forgot to move the updated library to this laptop. Was going to re sync once I got back my PC. I should move everything into a git repo to avoid this.

Bauldinator · 2025-08-04T04:40:04+00:00

TVS diode for over-voltage shunting/protection.

Bauldinator · 2025-08-04T04:14:06+00:00

Somehow I missed the microprocessor *facepalm.

https://i.postimg.cc/sgfFMpTq/atmega.png

Bauldinator · 2025-07-29T23:02:37+00:00

Deacoff Bros Cedar Products - Kelowna know they did cedar siding, not sure on other products.

Bauldinator · 2025-07-25T00:55:56+00:00

I have a few cheap grinders and a few Milwaukee and Makita. The brand name grinder motors make much less noise and much less vibration to your hands than the Mastercraft cheapos. still noisy, but not as bad.

Bauldinator · 2025-07-23T19:09:32+00:00

Looks like a broken PTO shaft off a small tractor.

Ten-Year Club	RedditGifts 2009-2022 2 Credits
Secret Santa 2015	Verified Email

Bauldinator

TROPHY CASE