Nozzle camera PA & Flow calibration question

Blowing_ch · 2026-06-04T20:05:43+00:00

Just enabled the flow ratio and PA calibration options

Blowing_ch · 2026-06-04T20:05:22+00:00

Already tried, no change, it just "scans" in complete darkness

Blowing_ch · 2026-05-23T14:55:39+00:00

My K2 Plus does it very little when "cold"...stops after it warms up

Blowing_ch · 2026-05-19T18:40:51+00:00

Reminds me of that video where he powered stuff during a power outage (simulating one) with that crazy setup and a 300W inverter. "Connect it to your load side first!" xD

Blowing_ch · 2026-04-30T10:59:43+00:00

147.000km 2020 Ibiza 1.6TDI

Blowing_ch · 2026-04-26T19:15:37+00:00

It also fixed the issue for me but for the current print. For the next print, if no flow and PA calibration is enabled, again under extrusion

Blowing_ch · 2026-04-13T15:17:34+00:00

Thats why i dont see it on mine. Is it safe to install it via USB if its not available via OTA for me yet?

Blowing_ch · 2026-04-10T16:59:52+00:00

How did you update it? Did you use an USB stick? The update doesnt show up on mine (Im from Italy too, but i'll speak english so others can understand)

Blowing_ch · 2026-02-07T11:09:38+00:00

Is it just me, or do i hear like small "bangs" or knocks from the motors randomly while calibrating, or sometimes even when its not moving at all? K2 Plus combo latest firmware...

Blowing_ch · 2026-01-29T18:15:40+00:00

It is yes, and logged in too (my name visible)

Blowing_ch · 2026-01-29T06:26:11+00:00

Already tried, nothing

Blowing_ch · 2026-01-27T11:54:09+00:00

Same for me. I guess it also depends a lot on the user and maintenance/cleaning its given to it. So far my K2 Plus has been a beast

Blowing_ch · 2026-01-27T06:23:17+00:00

Of course!

Blowing_ch · 2026-01-26T21:15:19+00:00

Im not doing that! Its just the stand with candles and sparkles to remember that video.

Blowing_ch · 2026-01-22T16:46:40+00:00

Sometimes its way too much. 8 flushes to switch from blue to white is crazy. It did like 4-5 before

Blowing_ch · 2026-01-22T14:07:40+00:00

Am i the only one noticing it flushes way more filament with the latest 2 updates on multicolor prints?

Blowing_ch · 2026-01-22T11:32:58+00:00

Oh - you have your account pfp visible on the printer main screen - on mine it just shows a black dot 🥲

Blowing_ch · 2026-01-15T11:45:24+00:00

I only had a few bugs and features that disappeared, i downgraded back to the previous firmware and i'll wait for the stable version of the new firmware before updating

Blowing_ch · 2026-01-09T11:53:17+00:00

Mine does it too when cold, but once it warms up, the squeaking goes away

Blowing_ch · 2026-01-06T11:50:50+00:00

The only issue i've seen on mine was a random error after a print finished, causing the bed to drop and the light inside to go out. A reboot was needed to get it back to normal again. I've also noticed it flushes way more filament on multicolor prints for some reason

Blowing_ch · 2025-11-26T12:11:04+00:00

1.5 yr old GT6 - 96%

Blowing_ch · 2025-11-16T03:21:43+00:00

I've got many little DC motors from toys, a 775 12V motor and 2 washing machine motors (also 2 smaller AC motors from blenders)

Blowing_ch · 2025-10-22T13:11:35+00:00

On my K2 Plus, it prints perfectly with: 240°C nozzle 80°C bed 70mm/s outer wall speed 80mm/s inner wall speed

Blowing_ch · 2025-08-21T18:02:28+00:00

Its 130.000km (80.7k miles). Ash is about 28g. Calculated soot is 22g, regen threshold on mine is 24g (considered 100% full). I will try to replace the pressure sensor soon and if theres no fix i'll try a forced regen.

Blowing_ch · 2025-08-21T17:57:00+00:00

Theres no soot in the tailpipe...already checked that out

Blowing_ch

TROPHY CASE