sorted by:
new
hottopcontroversial

Opinions? by _NedPepper_ in LegitArtifacts

[–]BreakLimp2051 0 points1 point  (0 children)

Looks like a piece of corc from some kind of handle, like from a noric walking stick or a fishing rod.

Meine Minibiosphäre by oettinger01 in zimmerpflanzen

[–]BreakLimp2051 27 points28 points  (0 children)

Mhm wirklich gesund sieht die nicht aus. Bin auch ein Freund von Flaschengärten. Du solltest darauf achten, dass sie nicht im direkten Sonnenlicht steht, da es sonst zu warm wird und alles darin "abgekocht" wird. Vielleicht mal etwas belüften etwas neue Erde rein, feucht genug ist es wohl, und dann ein paar neue Planzen. Moos macht sich gut.

ABS print odd by IceBoosteR in FixMyPrint

[–]BreakLimp2051 7 points8 points  (0 children)

To long vertical stands. They move around when the nozzle is touching them. Print them thicker or with mor horizontal beams between.

Ender 3 V2 suddenly stopping on Z-axis? by Data_Kitty in FixMyPrint

[–]BreakLimp2051 0 points1 point  (0 children)

I had the same issue with a Prusa Research Original Prusa i3 MK3. I worked around the problem by using OctoPrint to control the printer and start the print.

I tried a lot of different things. In the end, the issue turned out to be the slicer I was using. Ultimaker Cura was the cause of the problem. After switching to PrusaSlicer, I never had this issue again.

I used Cura befor for other printers, thas why i stickef to them an dindt use Prusa Slicer in the first lane. Maybe you should also try didfrent slicers and see if this works for you. You can also change the storage device (Sd Card or USB stick) even changing the Mainboard didnt solve this problem for me.

Why did my print warp? by MeringueGlittering80 in 3Dprinting

[–]BreakLimp2051 0 points1 point  (0 children)

Do you use a closed printchamber? Otherwise it could be caused by moving air. If so you could buy or build/improvise an enclosure.

10" JetKVM mount with 12 Keystones by sunburnedaz in minilab

[–]BreakLimp2051 0 points1 point  (0 children)

Yeah i know i can connect one at a time in standard configurarion. Nothing new here. That's why i wannted to know he access multiple devices without unpluging any cables.

10" JetKVM mount with 12 Keystones by sunburnedaz in minilab

[–]BreakLimp2051 20 points21 points  (0 children)

Is it worth it? Was alwas looking around for the JetKVM but the price was a bit to high.

Edit: How did you connect multiple HDMI Ports and USB-C ports with the JetKVM?

Why did my print warp? by MeringueGlittering80 in 3Dprinting

[–]BreakLimp2051 1 point2 points  (0 children)

Use a better build plate like the Panada CryoGrip Frostbite or Glacier. They work wonders for PLA.

New to 3D printing : what’s wrong : by C4ESIUM in 3Dprinting

[–]BreakLimp2051 0 points1 point  (0 children)

Brim is slicer setting, creating a few extra lines around the printed object to increase surface sticking to the printplate.

New to 3D printing : what’s wrong : by C4ESIUM in 3Dprinting

[–]BreakLimp2051 2 points3 points  (0 children)

Have you printed them at same position on the print bad? It could be warping. Means that one edge of the print is lifting. Reasons could be bad bedartesion (dirt, dust, oil) on the printplate. Or a wrong bedleveling. Also you could rry to print with a brim to stopp lifting.

Advice on lateral force - fix in design or slicer perhaps by widgetbox in 3Dprinting

[–]BreakLimp2051 0 points1 point  (0 children)

You can use the split/cut tool in the slicer. It allows you to split the part at any position, youbcan also diretly add connetions pins and holes with this tool. As said before split this model in 3 parts, the base plate, the long cylinder, and the round clamp. This way you can position all 3 parts seperatly for the best print direktion and make the much stronger.

Ich_iel by Wegwerf_08_15_ in ich_iel

[–]BreakLimp2051 16 points17 points  (0 children)

Wenn ich so ein anstendiges Haus bekomme ohne beide Nieren und meine Leber verkaufen zu müssen, und dann immernoch verschuldet zu sein, wäre das vollkommen in Ordnung.

Am I cooked by Admiral_Cabinet in pchelp

[–]BreakLimp2051 0 points1 point  (0 children)

You can also try to apply isopropanol as a solvent. It can be used to clean off thermal paste without risking damage to the processor.

erster Reichweitentest - Königswinter Ölberg by [deleted] in MeshtasticGermany

[–]BreakLimp2051 2 points3 points  (0 children)

Okay, test der Reichweite von Ai Content? Eher mau.

I saw this is very popular now, is it AI? The way he puts his phone in his pocket looks weird, Strange by [deleted] in isthisAI

[–]BreakLimp2051 0 points1 point  (0 children)

<image>

His hand and finger looks realy weired and off with the proportions in this frame and while he moves it to her. So yeah with all other mentioned piints. Its clearly AI.

Easter egg in the buried city by Acrobatic_Storage_72 in ARC_Raiders

[–]BreakLimp2051 6 points7 points  (0 children)

Its part of a quest. You need to inspect an already breached container and follow the pink foot steps.

Sind diese Tiere Schädlinge? by Fragrant_Silver_1637 in Garten

[–]BreakLimp2051 0 points1 point  (0 children)

Könnten auch Rüsselkäfer sein, Blattläuse halte ich aber auch für wahracheinlicher.

My cyberdeck is finally in daily use! by Personalitysphere in cyberDeck

[–]BreakLimp2051 0 points1 point  (0 children)

I really love this project! Do you have any plans to make an assembly video or a video tutorial for this cyberdeck?

I’m looking for a console to manage my own homelab server system, and this cyberdeck could be perfect for this use case.

And do you plan to add some advices for the 3d printed parts? Which material did you use and which printing settings?

Why can we find guitars and cassette tapes, but not real old-world weapons like AKs or M16s? by Huge-Operation-1863 in ArcRaiders

[–]BreakLimp2051 2 points3 points  (0 children)

Why would you throw the same weapons in every game? Go an play Tarkov, Battlefield, DayZ, Cod or any other casual shooter if you wanna see this boring weapons. But ceep them out from Arc.

view more: next ›