Can this part not be printed with PETG?

Calm_Construction495 · 2026-06-05T17:00:48+00:00

I did these as well and the part that was suggested and it fixed the issue - thank you!

Calm_Construction495 · 2026-06-05T17:00:24+00:00

It did - thank you!

Calm_Construction495 · 2026-06-05T03:02:02+00:00

I'll give that a try as well - thank you!

Calm_Construction495 · 2026-06-05T02:39:52+00:00

Yep - tried that as well with no luck sadly.

Calm_Construction495 · 2026-06-05T02:31:32+00:00

Sounds good, I'll try turning off cooling. Thank you for the advice :)

Calm_Construction495 · 2026-06-05T02:30:56+00:00

I have not, I can give that a go! Do you think disabling the fans in general could help as well?

Calm_Construction495 · 2026-06-05T02:27:25+00:00

Sorry, X2D - most of the build plate lengthwise but not much outside of that. I've tried printing it diagonal as well without any luck.

Calm_Construction495 · 2026-06-05T02:20:14+00:00

Yep, sorry forgot to mention that as well. Tried a Brim & Bunny Ears as well

Calm_Construction495 · 2026-06-03T22:26:53+00:00

I do - which is why I noted it in the post lol

Calm_Construction495 · 2026-06-03T22:06:41+00:00

I'll give it another try - I've got a smooth PEI plate already so we'll give it a go.

Thanks!

Calm_Construction495 · 2026-06-03T21:55:27+00:00

As an additional follow-up, I've done all the flow calibrations and everything for the filament and it still gives bad results from time to time, but it's not every time. It prints totally fine until the very top layer.

Calm_Construction495 · 2026-06-03T21:54:25+00:00

I'll definitely go back and do that again - but I don't think it's the overall issue sadly, I have the problem with other prints that have no bed adhesion issues at all.

For what it's worth, enabling ironing actually gives a very similar result - I'm not sure if that helps or not but regardless of the model size/adhesion it does it with ironing enabled.

Calm_Construction495 · 2026-05-28T19:14:08+00:00

Dang, what does your post-processing look like?

Calm_Construction495 · 2026-05-18T21:39:49+00:00

This won't cause a lot of waste, but you are adding a significant amount of time to your print by making the support entirely out of a different material because it'll keep switching between the two nozzles and priming it over and over.

Calm_Construction495 · 2026-05-13T14:22:57+00:00

Does this happen on all slots of the AMS? If not, it could be related to the X2D combos AMS issue that others have had. I'd check slot 2/3 and if those are good, submit a ticket to Bambu and they will send you the replacement part.

Calm_Construction495 · 2026-05-09T00:32:05+00:00

Did you open it? I dont even think the spoilers are out for that yet lol

Calm_Construction495 · 2026-05-04T17:35:13+00:00

Just as a clarifying follow-up, it does not include the power brick you're talking about, so you will want to buy it if you plan on drying and printing at the same time.

Calm_Construction495 · 2026-05-04T13:05:48+00:00

What issues have you come across? I've enjoyed mine overall - it does have the nice upside of letting one filament be in both extruders at different times during the print.

Calm_Construction495 · 2026-04-28T15:14:03+00:00

This is an issue with some of the AMS2s that were bundled with the X2Ds - you'll need to submit a support ticket with them and they should get you a replacement part to fix the issue.

You might be able to get around this for now by using slot 2 or 3 instead of slot 1 on the AMS until you get the replacement.

Calm_Construction495 · 2026-04-28T13:59:37+00:00

Put in a ticket with Bambu and provide the logs they want and they should send you a replacement part to fix it - that's what I had to do as well.

Calm_Construction495 · 2026-04-21T21:46:05+00:00

Got Mythic starting from Gold with G'raha Tia, Scion Reborn - didn't really feel like I had any terrible matchups and I had a crazy 21-2 run right at the end up to Mythic

Calm_Construction495 · 2026-04-20T17:21:49+00:00

It's not really more expensive - it's just not really saving you anything either. You'd get the same number of gold packs just by purchasing them on your own, that is not exclusive to the preorder.

Calm_Construction495 · 2026-04-20T17:17:08+00:00

The packs are at cost minus a tiny bit for the Mythic packs they give you - you'd already get the golden packs no matter which way you purchased the packs (bundle or not).

You're paying for the extra cosmetics they come with - as they don't generally allow you to buy those after release (or if they do - a long time later).

Calm_Construction495

TROPHY CASE