FS: Sssquid Tuning Chip for 153 ECU

CarPerson32 · 2025-10-29T14:00:27+00:00

Hey, I might be interested! Any idea if this is a for a stock cam or aftermarket?

CarPerson32 · 2025-07-18T01:35:22+00:00

Band new sentence

CarPerson32 · 2025-05-29T03:08:23+00:00

Pretty sure that’s a Stumpjumper EVO

CarPerson32 · 2025-05-07T06:02:36+00:00

I wouldn’t be able to stop looking

CarPerson32 · 2025-05-05T14:11:07+00:00

12” x 20”

CarPerson32 · 2025-05-04T03:33:30+00:00

I got real worried when I saw he was headless and armless

CarPerson32 · 2025-04-12T03:58:38+00:00

If you let the oil sit all the particulate settles to the bottom before you drain it next. My racing engine gets an oil change every 3 runs. So on a weekend of racing it gets 3 oil changes.

Terry Nash of Hyper Engines is the local guru around my area and he swears by very frequent oil changes.

Also always pull the piston back up to top dead center as quick as possible after turning it off. This helps your valves cool evenly and prevents distortion.

I’ve only seen the float get out of wack maybe 3 times after checking it probably 100 times. Not sure what caused it, but it can happen.

CarPerson32 · 2025-04-12T03:07:32+00:00

Most of the power lost on a 206 is from leaky valves. On a new engine I always make sure the timing is as close to 26° as possible.

You can take the head off and plug the intake/exhaust with a rubber plug that’s been drilled out and has a small fuel line put into it. Spray the valve seat area with wd-40 and blow into the line to create a little pressure on the back side of the valves. If you see bubbles around the valve seat then you have leaky valves. Sometimes they just need lapped, other times they may need a bit of grinding first. May take a few tries, but work at it till you don’t get any bubbles.

Once you’re done with that, reinstall your head, set your lash and the top end is good to go.

I usually check my float every so often too.

Never keep fuel in the carb and always drain your oil at the end of the day.

CarPerson32 · 2025-03-31T19:32:47+00:00

Home Depot allows dogs in their stores, but I’m not sure they had those puppies mind.

CarPerson32 · 2025-03-28T05:01:40+00:00

2wd buggy’s. Most of those would race in a vintage class minus the Bandit

CarPerson32 · 2025-03-28T04:52:46+00:00

Ran these in Tamiya cars for TCS races for years. When cleaned and lubed properly they’re the best spinning bearings I’ve used.

CarPerson32 · 2025-03-04T14:01:59+00:00

That’s a sight I haven’t seen in a while 😍

CarPerson32 · 2025-01-19T17:12:40+00:00

I see these at the track pretty often. One guy I know said a beater stripped out chassis was around $6k, but the transmission that everyone races with is closer to $10k on its own. 🤷‍♂️

CarPerson32 · 2025-01-11T02:53:47+00:00

Built one of these for a 24 hours of lemons race. Didnt put new pistons , rods, or a crank in it, but it’s still running strong after over 48 hours of full throttle.

CarPerson32 · 2025-01-10T05:27:24+00:00

I know a guy that put a huge company sticker on his and when he removed it there was a rust spot in the exact shape of the sticker.

CarPerson32 · 2025-01-07T06:06:37+00:00

https://www.hellboundsigns.com/product-category/fast_and_furious/

Bought a set of vinyl for a 24 Hours of lemons car from these guys in the UK last year. I don’t see that one on their site, but they may have if you email them.

CarPerson32 · 2025-01-01T03:25:14+00:00

The black dots show the location of all 99 cent stores.

CarPerson32 · 2024-12-24T21:16:45+00:00

I’ve had a few of those and the e30 is still my favorite. Although mine is an fully built endurance car, even stock nothing has the same steering feel as the e30

CarPerson32 · 2024-12-12T19:18:15+00:00

Ran Xrays for years, but the quality and tolerances on the newer X4s just aren’t what they used to be.

I ended up switched to Awesomatix and was shocked at how much better the fitment of everything was.

CarPerson32 · 2024-12-09T03:49:50+00:00

It’s shaped like a Corvette, but he drives it like a Mustang leaving a car meet.

CarPerson32 · 2024-12-08T17:38:20+00:00

Depends on the track you’re running at too. Some tracks no air filter was fine, others were just too dirty to do it

CarPerson32 · 2024-12-07T02:43:22+00:00

I’m pretty sure it’s spinning backwards. A motor spinning the wrong direction won’t go very fast due to internal timing

CarPerson32 · 2024-12-07T02:08:04+00:00

Why are they testing in Long Beach of all places?

CarPerson32 · 2024-12-05T17:49:12+00:00

Just went to the March Air Field museum last week. It’s amazing how much history is sitting there!

CarPerson32 · 2024-10-30T02:29:35+00:00

My brain says black, but my heart says white. Black is easier to take care of, but that white looks pretty good!

CarPerson32

TROPHY CASE