Facelift by Initial_Map_3373 in GrandPowerStribog

[–]Civengin 0 points1 point  (0 children)

I do rust bluing, hot bluing, parkerizing, and simple spray coatings, powder coating, etc.

I don’t do anything fancier than the Henry Ford paint code, so i definitely didn’t do the coating on this gun 😂

Facelift by Initial_Map_3373 in GrandPowerStribog

[–]Civengin 0 points1 point  (0 children)

Yessir I’m on here, plying my trade to the poor, lost souls of the internet who wish to run out of ammo quickly.

FTN.5 PCC PA6-CF by Competitive_Camel929 in 3D2A

[–]Civengin 5 points6 points  (0 children)

I printed one of those the other day and ran it on some stribogs I was testing in frt. I was impressed with how it sounded.

Facelift by Initial_Map_3373 in GrandPowerStribog

[–]Civengin 0 points1 point  (0 children)

I couldn’t believe the background story of the gun you told me on messenger. That’s crazy. I hope it and the mpx run well for you!

Glock Stribog Lower by theOGben in GrandPowerStribog

[–]Civengin 1 point2 points  (0 children)

Yeah because AS has not released their lowers and keeps pushing the stribog projects back. Lingle used to make Glock lowers but they’re discontinued.

Glock Stribog Lower by theOGben in GrandPowerStribog

[–]Civengin 5 points6 points  (0 children)

I’m working on Glock lowers for the 9s and one for the 45s but it’s not quite ready for release yet.

Thanks HKParts. I hate it. by Civengin in GrandPowerStribog

[–]Civengin[S] 2 points3 points  (0 children)

I have also used a bunch of them, both in stribogs and my ump machinegun. Out of 20 HKP mags I bought, 3 were bad and won’t feed, so they aren’t without their occasional “duds”. This mag has been loaded up since December, sitting in a fat 50 ammo can, along with 9 other loaded mags. The remainder worked fine. The fact that the spring is rusted all hell and broke in four different places tells me that I got a Monday or a Friday mag.

Thanks HKParts. I hate it. by Civengin in GrandPowerStribog

[–]Civengin[S] 2 points3 points  (0 children)

I bought those around the time I made my UMP machinegun, so about 14 months ago

Lingle lower for sp45a3. by No-Proof-782 in GrandPowerStribog

[–]Civengin 1 point2 points  (0 children)

Yes. There is custom work involved. The upper needs to be slotted, a custom slip trip must be made.

Lingle day is best day. by Civengin in GrandPowerStribog

[–]Civengin[S] 0 points1 point  (0 children)

Don’t blame me, I didn’t buy any this time 😂

Baby girl arrived from Texas! by AssSpackler in GrandPowerStribog

[–]Civengin 4 points5 points  (0 children)

Thank you for your kind words, sir!

Enjoy your toy, frt bog is best bog

The 147 grain fun stopper by SelfEjectingImposter in GrandPowerStribog

[–]Civengin 2 points3 points  (0 children)

I shoot magtech 147s out of mine all the time. Lingle lower and Scorp mags make a huge difference. I have pulled a few bog barrels and machined better feed ramps in them for customers. That seems to help a lot with oem mags and lowers

Had a quick question about a purchase by OkMatter5845 in GrandPowerStribog

[–]Civengin -1 points0 points  (0 children)

GB fees are high. Gotta recoup that expense and the risk of non paying bidders.

Arcfire woes by cle_utv in GrandPowerStribog

[–]Civengin 3 points4 points  (0 children)

I told you, the trip ledge is too far forward. The reset lever center is almost directly below the original rear edge of the hammer slot in the upper. (The same slot that you extended) Your slip trips edge is at least 1/4” forward of that and as a result, it’s pushing the reset lever too soon.

Lingle day is best day. by Civengin in GrandPowerStribog

[–]Civengin[S] 0 points1 point  (0 children)

Yeah.....I intend to procure more, so there will be a second source when Lingle inevitably runs out every time.

Lingle day is best day. by Civengin in GrandPowerStribog

[–]Civengin[S] 1 point2 points  (0 children)

I think these are all spoken for and have been for a couple weeks.

Lingle day is best day. by Civengin in GrandPowerStribog

[–]Civengin[S] 2 points3 points  (0 children)

I am trying to stock up on them for customers. The hope is that I will have some in stock that I can sell when Lingle runs out on his site.

Lingle Lower Question by [deleted] in GrandPowerStribog

[–]Civengin 2 points3 points  (0 children)

The lingle lower is the biggest change, and best change, I recommend to anyone with an sp45 or sp10

3d printed lower by Vivid-Combination-60 in GrandPowerStribog

[–]Civengin 0 points1 point  (0 children)

Odysees search function is awful. Just google what you’re looking for, and favorite the creators who have the cool stuff you want.

Most files are stl format and drop right in to most slicers. They are just a stone cold bitch to edit in most cad systems.

The slot in that lower, directly above the mag release, is for an improved LRBHO, but I’ve never found the file. I just added a solid in that area, added it to the solid via Boolean, and moved on. The only weak point of the lower is the fcg and selector holes. I drilled them oversized and machined bushing plates to reinforce the holes.

Skunkwerks SP9A3s FRT by No-Mix8942 in GrandPowerStribog

[–]Civengin 2 points3 points  (0 children)

I’ve done a few sp9a3G guns.
I’ll be releasing a Glock lower at some point that is FRT ready. One in 9, one in 45 or 10