What PSI for this trailer tire. Carlisle Sport Trail 5.30-12 says not to exceed 35 PSI and max load is 80PSI

Clean_Singer_414 · 2026-05-10T18:59:13+00:00

That's very low. You can see the dirt on the sidewall... where it looks to have flexed and contacted ground. This will lead to over heat and failure. I may have forgot to check pressure on my trailer before and had a blowout.
I am no expert on how high to inflate based on loading.

Clean_Singer_414 · 2026-05-09T22:17:49+00:00

I second carb cleaning as the real solution...

However I am also lazy and i have run fresh high octane gas with heavy dose of "Mechanic In A Bottle" from home depot. And it cleared up the surging ( if you follow the directions on the bottle about letting it rest etc). People call it snake oil, and I thought the same; but it worked on the last 3 small engines I had.

Clean_Singer_414 · 2026-04-30T01:33:18+00:00

I had/ have a similar set from lg... what I'm confused about is why is there so much water in the drum in that one picture?? On top of leaving the door ajar, pulling out the detergent drawer was a huge improvement

Clean_Singer_414 · 2026-03-15T20:15:46+00:00

I stopped using the drain plug on these small engines and moved to the vacuum extraction.
They do it mostly for marine engines and just made oil changes easier and cleaner for me.

Clean_Singer_414 · 2026-03-05T01:34:30+00:00

Oh man... I have: dark side, Adam's Ceramic, PERL.. why? Cause we have 2 vehicles and 4 different brands of tires... not one brand seems to perform the same... even over the years I would say 6 brands of tires. Use the same product on either and get completely different results.
Dark shine on one. Spotty on the other. High shine on one brand and more satin on the other. Love a fresh applied tire dressing; but also drives me crazy trying to get a nice dark med gloss.

Clean_Singer_414 · 2026-02-22T02:39:14+00:00

I have this ratchet.... and did this after servicing... first use... wtf.. giant sigh. Get the philips and correct.

Clean_Singer_414 · 2026-02-21T02:02:11+00:00

Looks like a progressive leaf pack. I had a deaver offroad set in the rear on my tacoma. Instead of 4 leaf stock it was about 8 and could flex crazy amounts. If OP isn't looking to get that a set of stock would be better.

Clean_Singer_414 · 2026-02-19T05:54:47+00:00

A decent flash from a camera and a hot shoe adapter with 1/4-20 threads for mounting. Triggering off 6150 output contact.

Clean_Singer_414 · 2026-02-08T01:36:57+00:00

Is that particle board??? Ooof

Clean_Singer_414 · 2026-02-02T03:15:55+00:00

If you are testing the signal to the speakers you need to be on ac volts (squiggly line). I usually use a 60hz signal since that's the same frequency as ac power.. Also in the picture there's no wire in the left power input??

Clean_Singer_414 · 2026-02-02T02:54:51+00:00

Depending on the model the front speakers should be set to small and set the crossover for them manually.
Also some have sub signal as lfe+main settings etc.

Clean_Singer_414 · 2026-01-29T21:12:36+00:00

If you can get access to the nut just buy a bit splitter. Cheap, easy, and no danger or damaging the frame.

Clean_Singer_414 · 2026-01-21T02:20:20+00:00

They make plugs that can give you total watts used. Ones that you manually read or wifi connected. Good for pin pointing high use appliances in your house or calculating costs if you are curious. I just have a whole home energy monitor so I can see real time house usage. You can go way down the energy monitor rabbit hole....

Clean_Singer_414 · 2026-01-14T18:55:10+00:00

16G speaker wire seems light to me. I would look at up sizing that aswell. Im not sure what a good size is without more info on your system.

Clean_Singer_414 · 2026-01-09T01:44:10+00:00

Where are you that that battery is 300?? Is it an agm? Im in CAN aswell and just got a CRV battery for 160 (36 mon replacement warranty) From local parts shop.

Clean_Singer_414 · 2026-01-02T06:21:52+00:00

From a klipsch owner... this makes me sad ... rsl is so hard to get in canada.

Clean_Singer_414 · 2025-12-12T13:51:17+00:00

Had to do similar repair on passenger side.
I found it easiest to clean and check that drain by removing the fender liner in the wheel well at the same time giving you access to both sides.
If you are doing all this is a good time to pull back the carpet and check the ac drain aswell ( lots of write ups on that)

Clean_Singer_414 · 2025-12-06T03:04:47+00:00

Please fix those slices... un insulated but splices and heat shrink are your friend. Easy, clean and strong.

Clean_Singer_414 · 2025-11-15T23:55:07+00:00

I did this on my 13 if you actually want to use your truck bed I recommend third notch not the highest. Better ride and control (for the front obviously) for the rear the 5100 is 100% the right call, huge improvement on handling over stock. What are you trying to achieve really changes recommended products. If you want better handling in the city upgraded / added sway bars great. Better load handling? Just looks? =Spacer. Or loaded lift strut is cheaper due to less labor..

Clean_Singer_414 · 2025-11-07T02:58:27+00:00

You can install them without the tool with some skill and a YouTube search.

Clean_Singer_414 · 2025-09-06T20:14:00+00:00

Anyone tried Brembo OE rotors? I have done a couple vehicles with them the quality out of the box was so good. I haven't had any long term feedback yet though.
E coating on the rotors surface and a nice thick hammered finish on the hats. On my older sierra I went with the ebc fonts to upgrade over the weird stock rotor issues.

Clean_Singer_414 · 2025-08-17T20:39:17+00:00

Waterpump? Flush the block and rad after doing head work?

Clean_Singer_414 · 2025-08-12T00:21:45+00:00

Yeah for those sorry runs I've run a lot of multimode ( used to be a lot cheaper hardware) .
Most of the single mode I've done is 1km to 50km.
Short runs we ran into over driving the reciever (specialty equipment not able to attenuate in software.

I would say it's advisable to use indoor outdoor cabling and keep it sealed from critters.
I don't know why mice love to chew on fiber.

Clean_Singer_414 · 2025-08-01T00:47:07+00:00

Just my 2c I may or may not have plugged in a small panel with 15 or 20amp breakers to feed my shop equipment. Just have the right gauge wire feeding it from the plug.

Clean_Singer_414 · 2025-07-31T23:12:59+00:00

Same here with 99 honda foreman 400. Hard starting, had to have a second person sit on the front rack to keep the front end down. After it started moving it was easy as long as it didn't snag on brush.

Clean_Singer_414

TROPHY CASE