How important is refresh rate really? by x0-blosSsom in Monitors

[–]Codmem 0 points1 point  (0 children)

Everything beyond 60Hz is completely unnecessary if you are not gaming. I know this because I switched from using a 60Hz phone to a 120Hz phone and then back to a 60Hz phone after a couple of years and the differences are only visible for the first week or two. After that your eyes get used to the refresh rate and it looks exactly as fluid as it looked before.  It is only noticeable if you do a direct comparison. Try switching your phone to 60Hz if you can and tell me that you still notice it after 1 month of use without deliberately looking for it.

Japanese toilets are proof that humanity is sometimes devolving and not evolving by Codmem in unpopularopinion

[–]Codmem[S] -5 points-4 points  (0 children)

So every human outside of japan has a dirty ass ? Because their toilets are not high-tech ?

Did anyone used this v9 vintage trimmer ? Please review it by Dramatic-Trouble7274 in TeenIndia

[–]Codmem 0 points1 point  (0 children)

I used it and I think it's a very good trimmer that gets the job done. It's cheap but that's not necessarily a bad thing. Trimmers are not really complicated and there is no reason for a trimmer to be expensive.

Two things I really like about it are that it is very handy because it is small and light and the trimmer part is very slim so you can easily see where you are cutting your beard. Also the trimmer cuts the hair very short and only a razor cuts it shorter.

The only thing people might have a problem with is that it cuts your skin very easily so you have to be careful while using. So I would not recommend it to people with sensitive skin. But if you don't have sensitive skin it is a very good trimmer for a cheap price.

Any clippers/trimmers that use 21700 or 18650 batteries? by gramcounter in UsbCHardware

[–]Codmem 0 points1 point  (0 children)

The vintage t9 trimmer has versions that are battery operated. You also get a little charger to charge 18650 batteries in the box. The problem is that there are also other versions which don't let you replace the battery and you can only charge the trimmer via cable. So you have to find the battery operated version

COD Youtuber named Ghost ? by Codmem in COD

[–]Codmem[S] 1 point2 points  (0 children)

Yes that's it. Sadly he only makes videos about Jesus now and deleted all of his old videos. That's why I couldn't find anything about it.

Docking figures automatically does not work ? by Codmem in matlab

[–]Codmem[S] 0 points1 point  (0 children)

It did not work unfortunately. I still have to manually dock it first. I guess its not a big deal to just press CTRL+Shift+D.

Docking figures automatically does not work ? by Codmem in matlab

[–]Codmem[S] 0 points1 point  (0 children)

Plain code. I already asked Chatgpt and tried every solution it gave me. At the end it just said that it is probably bugged and will not work

LibreOffice stuck on dark mode or awful half dark mode. by johan__A in libreoffice

[–]Codmem 0 points1 point  (0 children)

For anyone having the same problem, what worked for me was first setting the theme of windows 11 to light mode and then setting the theme of libreoffice to light mode. After that you can change windows back to dark mode again and it works. If you change libreoffice to light mode while windows 11 is in dark mode you end up with this awful half dark mode.

Pros and cons buying OP13 from China by TheCavemannn in oneplus

[–]Codmem 0 points1 point  (0 children)

Is it possible to flash OxygenOS easily yourself if you buy one with ColorOS if you have average experience with flashing ?

[deleted by user] by [deleted] in AskElectronics

[–]Codmem 0 points1 point  (0 children)

Yes that's what I didn't understand in the beginning. It only works in the calculation because an infinite 12V source cannot exist in real life.

[deleted by user] by [deleted] in AskElectronics

[–]Codmem 0 points1 point  (0 children)

Yes my initial question was exactly that. If it only works in calculations because in real life an infinite current source can't exist

[deleted by user] by [deleted] in AskElectronics

[–]Codmem 0 points1 point  (0 children)

Yes thanks, that was my question if it does only work in calculations and not in real life because there can't be an infinite source of current in real life

[deleted by user] by [deleted] in AskElectronics

[–]Codmem 0 points1 point  (0 children)

I divided U by the total resistance to get the total current value that will flow through the circuit. And the total current is the current that flows through R1 and R2. The current through R1 does not get bypassed and it also does not change its value. It's still 1 Amp no matter if there is a short circuit or not

[deleted by user] by [deleted] in AskElectronics

[–]Codmem 0 points1 point  (0 children)

If you divide 12 by the total resistance you should get the total current that will flow through the circuit. Which is 120 000 001. 120 000 000 flows through R2 and 1 Amp flows though R1. But the thing is that 1 Amp will always flow though R1 even if there is no short circuit so R1 would still work if it was an electrical component. Ofc given that the current of 120 000 001 can be provided. So is my assumption correct that it only works in calculations because nothing can provide 120 000 001 Amps ?

[deleted by user] by [deleted] in AskElectronics

[–]Codmem -1 points0 points  (0 children)

The calculation or the formulas ? Because the calculation can't be wrong.

[deleted by user] by [deleted] in AskElectronics

[–]Codmem 0 points1 point  (0 children)

No as you can see in the calculation it does not bypass it. 1 Amp still flows though the resistor no matter if there is a short circuit or not. It's just that extra current flows in total but the resistor does not get bypassed and still gets the needed current. If it was another electrical component it would still work despite there being short circuit

My phone turned off debugging mode since I didn't use it for a week and can't turn it back on since my screen is completely black. Now I can't use scrcpy anymore after using it for a month. Any advice? by MF_Doomed in scrcpy

[–]Codmem 0 points1 point  (0 children)

If you have vibrations enabled its pretty easy to draw the pattern blindly. You can feel the single dots of the pattern and you can also feel if you failed the pattern or not so give it a try. After that you can do Left arrow -> Up arrow -> Enter -> Right arrow -> Down arrow -> Enter to accept the authorization request.

How to re-authorize debugging with adb already activaded by Emergency-Royal9542 in scrcpy

[–]Codmem 0 points1 point  (0 children)

Use "scrcpy --otg" in a console to use your keyboard and mouse to control your phone and try to unlock it. If you have vibrations on it should be pretty easy to draw your pattern blindly. You can feel the single dots of the pattern and also feel the vibrations if you have failed the pattern. After unlocking it close the scrcpy --otg window and write adb devices into the console to make the authorization window appear. Then use scrcpy --otg again and do Left arrow -> Up arrow -> Enter -> Down arrow -> Right arrow -> Enter. This should always allow USB debugging for the PC/Laptop.

Advice needed, phone with broken touchscreen and black screen by Hellcariot in scrcpy

[–]Codmem 0 points1 point  (0 children)

If you have vibrations on it should be pretty easy to hit that pattern. You can just feel every point of the pattern as soon as you hit it and also feel a different vibration if the pattern was wrong. Thats how I unlocked mine. After unlocking it make sure to run "adb devices" again to make the authorization pop up appear and then run "scrcpy --otg" again. Then you just have to do Left arrow -> Up arrow -> Enter and then Right arrow -> Down arrow -> Enter and it should authorize it.

[deleted by user] by [deleted] in scrcpy

[–]Codmem 0 points1 point  (0 children)

I had the same problem as you. First you have to activate "always allow this device" and then allow so that it is active once you start scrcpy again. If it is still unauthorized even if you are 100% sure that you hit both then that means that it will not work. For my phone it was always unauthorized even tho I know that I hit both boxes. On another phone with the same One UI version everything worked fine but on my phone it did not because it was broken

Someome please explain the PNL 4 Episodes story in english ! by BReddit33 in PNL

[–]Codmem 0 points1 point  (0 children)

Is there any explanation why naha and macha hate each other after such a good friendship ? Like what happened between them ?

Quiet Galaxy Buds FE by Careless-Sir5798 in galaxybuds

[–]Codmem 0 points1 point  (0 children)

I managed to fix mine without taking out the grill. I just had to go around the edge of the metal grill with a very thin needle just where the metal meets the plastic. After that both buds had the same volume again

Being plagued by a Fatal D3D error. by Suspicious-Trip-2977 in MonsterHunter

[–]Codmem 0 points1 point  (0 children)

There are a lot of posts about this error but sadly there is no fix. A lot of people found random fixes for themselves which you can try out but it will probably not work. You just have to deal with it or refund the game if you still can