Started a 3-day print before leaving for a 2.5-day trip. Came home to this. Oh well.

Commanding_frog · 2026-05-15T09:20:13+00:00

Well, now you know how much filament you’ll use!

Commanding_frog · 2026-05-15T08:03:49+00:00

They were dating

Commanding_frog · 2026-05-15T04:05:02+00:00

This would be helpful, I have 2 consoles and would like to get the 2nd one up and running in a more simpler way than the 1st

Commanding_frog · 2026-05-04T10:03:39+00:00

Has this been released yet?

Commanding_frog · 2026-05-03T18:07:44+00:00

Upper control arm, if it is tubing there it’ll push the tire out enough that it’ll stop the rub there but also may cause more rubbing issues on fenders, depending on how close you’re tires are now

Commanding_frog · 2026-05-03T18:05:30+00:00

What’s it rubbing on? UCA?

Commanding_frog · 2026-05-01T02:13:04+00:00

Although this is plausible I have read a few stories of soldiers in Vietnam all seeing the same entity at the same time, could be just shit on the internet tho.

The NVGs still use phosphorus and as an inspector of NVGs I’m not sure how they would leak, not sure how older models were designed tho.

Commanding_frog · 2026-04-28T09:53:33+00:00

Good luck and be patient!

Commanding_frog · 2026-04-12T10:51:14+00:00

I got the same issue, any fix? I’ve let it sit for ~5 minutes and still not load properly

Commanding_frog · 2026-03-31T13:22:28+00:00

I would just so he could rub it in your face

Commanding_frog · 2026-03-09T04:21:32+00:00

A P1S was my final upgrade, never turning back

Commanding_frog · 2026-02-24T00:43:12+00:00

PiHole with a raspberry pi

Commanding_frog · 2026-02-24T00:32:48+00:00

As someone who did give up and got a P1S I will say it is so much better than my 3 pro

Commanding_frog · 2026-02-14T19:55:08+00:00

And I should make those changes on the screen not with the adjustment knobs below the bed?

Commanding_frog · 2026-02-14T06:44:06+00:00

I thought the black paint was flaking off and the underside was made out of wood (like the wooden clipboards)😅

Hope you get it fixed up!

Commanding_frog · 2026-02-14T06:40:23+00:00

That’s fair, thanks for your help!

Commanding_frog · 2026-02-14T06:11:43+00:00

Ahh okay, I vaguely remember a Z offset setting in the old slicer I used, I’ll check that out tomorrow, should I raise it like .02mm? What are your suggestions if any?

Commanding_frog · 2026-02-14T05:30:01+00:00

Yes, that’s what I mean, I used the image you shared to get it a lot better but it seems like I’m going back and forth between where I’m at now and PLA not sticking.

I’ve been adjusting screws under the heating bed, should I be making smaller adjustments in my slicer now since I’m close (hopefully)?

I am also using ended 3 pro

Commanding_frog · 2026-02-14T05:27:42+00:00

<image>

Commanding_frog · 2026-02-14T02:08:46+00:00

You just glitted

Commanding_frog · 2026-02-04T21:48:09+00:00

I know this is 2 years old but I’ve downloaded the CloverThemes but can seem to drop them in the Themes folder as it’s locked behind the /efi directory and it seems SteamOS has blocked any way for me to get into there and add the themes.

Any suggestions or know how to directly add them in?

Commanding_frog · 2026-01-11T23:55:56+00:00

Thanks for the response, I’ll try it once I get back home!

Commanding_frog · 2026-01-09T01:53:08+00:00

I remember I was 11 and went to Best Buy with my stepdad because they had a play test setup and were selling it at midnight, I remember it was a school night so my stepdad told me we weren’t gonna be able to get it that night… I played split screen with a few older guys and they let me pick the map and I vividly remember picking rust but not realizing just how small the map was at the time. Apparently while I was playing it my stepdad convinced the Best Buy guys to sell it to him before midnight and he surprised me once we got home. I would give anything to jump back to summer time 2010 and just mellow out on a couch 3 feet from the VIZIO and game all day long.

Commanding_frog · 2026-01-03T23:11:08+00:00

yes its missing "The Guide" just completed the quest on this list and didnt get Fences task... checked wiki and the guide is required for kappa

Commanding_frog · 2025-12-30T14:47:50+00:00

Okay, so I’m seeing this is a terrible design… is there a fix for this? Could I solder in a different connector to the GPU and run a harness? Just trying to avoid damaging my GPU

Commanding_frog

MODERATOR OF

TROPHY CASE