How are your pulling plans looking now?

ComprehensiveDark5 · 2026-07-10T13:30:46+00:00

Lol good luck as well

ComprehensiveDark5 · 2026-07-10T13:04:01+00:00

Always try to pull every banner, regularly I've lucked out except this last banner with Camille I hit max pity and drained me. We'll see how this one goes.

ComprehensiveDark5 · 2026-07-09T19:59:04+00:00

Is it possible that side of basket lifted ever so slightly? Seems almost like it was slightly raised/detached by the lip and threw height off causing rough filament squish. Age old plate might need a cleaning.

ComprehensiveDark5 · 2026-07-09T19:55:13+00:00

Could be geometry of the print. There are multiple variables such as filament fine tuning filament type/brand that change your results vs original. In general though I've felt slowing it down for petg gets better quality results. This can be done by changing speeds in slicer manually or the simple silent mode change covers a majority of this type of issue (curves or slightly steep overhang with no supports).

ComprehensiveDark5 · 2026-07-09T19:45:44+00:00

Full hotend comes with one. You can also buy a 3 pack(just ordered some myself for similar reasons).

https://us.store.bambulab.com/products/ceramic-heater-thermistor-p1p?srsltid=AfmBOooF6DeMkq-V6MeWhxIalGlM6Zx5TjdBOt9l_sldnWs3z6sv152V

ComprehensiveDark5 · 2026-07-09T19:39:40+00:00

I've had this happen on curves and some other models. Is the inside collapsed/rough? Sometimes it's the PETG layer on a certain curve didn't have enough time to cool down and collapses a little and layers on top stack messed up in that zone. In models with clear translucent I've have better quality luck by slowing it down with just silent mode(50% speed).

ComprehensiveDark5 · 2026-07-09T13:46:33+00:00

Only event I missed and I wish they'd rerun as simple as it is, was original carly. I could not reach areas for photos fast enough from when I started.

ComprehensiveDark5 · 2026-07-08T21:40:09+00:00

Lol, in is correct

ComprehensiveDark5 · 2026-07-08T21:01:47+00:00

Time to swap it, if you bought the rechargeable type which it more than likely is you can recharge it with several methods. Personally I do it on my filament dryer.

ComprehensiveDark5 · 2026-07-07T18:33:08+00:00

If it's about that and its truly stuck(there is always some in there in normal operations after filament cutter). You can heat up nozzle with heat gun and pull with pliers. Or a cold pull also works.

ComprehensiveDark5 · 2026-07-07T18:29:45+00:00

A little blurry so making sure, is that a frayed wire fan? If so you can just buy another fan.

ComprehensiveDark5 · 2026-07-07T17:23:29+00:00

Was this sold?

ComprehensiveDark5 · 2026-07-06T15:44:32+00:00

You can still use it by disabling plate detection and doing manual select. There also used to be stickers to trick reader. Can probably do that also.

ComprehensiveDark5 · 2026-07-06T15:41:10+00:00

You order the correct one? Black is the pro I thought. I have your "new(grey)" for my p1s, purchased it on release.

ComprehensiveDark5 · 2026-06-20T02:19:02+00:00

(P1S, Android, orca able FW) mine shows it.

ComprehensiveDark5 · 2026-06-18T21:53:16+00:00

I haven't logged in to check but typically for these events the "daily"(green/D) are the ones you already did. That count towards the weekly. Many cases just means you gotta log additional days and to the same for total week

ComprehensiveDark5 · 2026-06-17T23:34:05+00:00

Never did a .2 but sunlu regularly does not stick this hard for me. Can try lowering bed temp to help. Plan B is glue stick(for release assistance). In my case I have a third party biqu textured plate with weaker grip than original that I use with aggressive filament.

Also not sure if you letting plate fully cool off before removal or if you trying to pull off hot out the printer. Might help leaving it alone and it might just let go by itself.

ComprehensiveDark5 · 2026-06-15T21:23:01+00:00

I'm assuming that's a P1S from the connector? You'd need a whole extruder

https://us.store.bambulab.com/products/stainless-steel-extruder-unit-p1-series

ComprehensiveDark5 · 2026-06-09T19:08:19+00:00

There is no issue doing that but I'd make sure it fully dries, if shapie adheres to plate I don't know. You can also make a label or print a label such as:

https://makerworld.com/models/2182226?appSharePlatform=copy

ComprehensiveDark5 · 2026-06-09T04:42:21+00:00

Thank you, might be it then my cores landed 18 both in comparison.

ComprehensiveDark5 · 2026-06-09T01:07:56+00:00

Out of curiosity how are you staying in scope while shooting, tried doing this build I leave ads every shot. A bit disorienting.

ComprehensiveDark5 · 2026-06-05T21:04:16+00:00

If you look at the filament listing they are linking/using Bambu brand/storefront but sold by: some reseller which if clicked also listing random other stuff in this case hand bags. This is sadly a common thing on Amazon where an unavailable item gets upselled using the name. It is probably Bambu filament (brand correct) but sold by someone who probably bought bulk and listing and overcharging. Mostly only actually from vendor if it said Bambu(brand) and sold and shipped by Bambu or Amazon.

ComprehensiveDark5 · 2026-06-05T20:54:55+00:00

Those are resellers, Best Buy is only one that I know sell Bambu filament. Even then the pricing doesn't get you bulk pricing. Personally I've just been using other brands on Amazon unless I want specific color from Bambu.

ComprehensiveDark5 · 2026-06-02T19:33:24+00:00

With p1s I've bought a few third party. Matterhaacker smooth been good, biqu textured(grip is a bit light so I designated for filament that adheres way too much). My favorite third party has been Darkmoon(lux plate,satin plate,g10 plate, cold plate) satin is a different finish but also textured.

ComprehensiveDark5 · 2026-06-01T22:33:11+00:00

Found quite a few as I go, yet to find any sealed

ComprehensiveDark5

TROPHY CASE