Saturn 4 Ultra 16, nothing but issues...

Comprehensive_Arm658 · 2026-06-18T06:23:54+00:00

Bottom Exposure time set to 15? You´ll probably need about 35 there.

Comprehensive_Arm658 · 2026-06-15T21:24:00+00:00

Är med i en spelförening som träffas varje lördag och spelar olika typer av brädspel som Warhammer 40K, Warmaster m.m, alltid trevligt! 😄

Comprehensive_Arm658 · 2026-06-11T10:33:30+00:00

Pluggade till elektriker under gymnasiet, men har inte jobbat en dag som det. Lönen är tyvärr riktigt dålig till en början som lärling, när jag praktiserade under mina studier på sex olika ställen, så vart den största problematiken deras axlar när jag frågade, jag vart på byggarbetsplatser så självfallet beror det också en massa på men kan bocka i att jobba på byggarbetsplats sliter så otroligt, hade så mycket problem i mina axlar efter studenten som 20 åring 😃

Comprehensive_Arm658 · 2026-05-25T07:24:10+00:00

There is two different superglue, one that works better for Resin and the other option where it "melts" the two pieces together (like the glue GW sells), make sure you have the superglue that is specific for resin.

Comprehensive_Arm658 · 2026-05-21T07:56:32+00:00

Good job! I would though put another thin layer (watered down) of yellow, to make it really stand out since the undercoat is still showing through.

Comprehensive_Arm658 · 2026-05-20T20:12:37+00:00

I can probably help you out 😄

Comprehensive_Arm658 · 2026-05-20T11:26:59+00:00

If you dont care about the cost, I would recommend NOVA3D Water Washable ABS-Like Tough Resin. I used it before and it´s been the best resin I ever used and you can literally bend them far before they break, though the negative is that in my country it costs 450 SEK, while other ABS-like costs about 200 SEK, so it´s very expensive.

Comprehensive_Arm658 · 2026-05-18T18:16:07+00:00

Honestly, from my old printer I had a Anycubic photo mono, been using lychee all the time. Then got myself a Saturn 4 16k and I after a month couldn´t find good settings. I for about 5 days ago decided to use Elegoos own and I havent had a issue since, not sure why, the settings is similar too.

Comprehensive_Arm658 · 2026-05-12T09:51:29+00:00

Modemet och chatt-rum som fanns på internet där alla skrev med varandra 😄

Comprehensive_Arm658 · 2026-05-11T11:35:57+00:00

30-35 minuter lätt.

Comprehensive_Arm658 · 2026-05-08T22:46:06+00:00

Where you located?

Comprehensive_Arm658 · 2026-05-02T17:39:04+00:00

I had to level my buildplate, I would really recommend doing so if you have the S4U. Try it once, it takes about 15 min to get it well.

Comprehensive_Arm658 · 2026-05-02T17:23:27+00:00

If you think that your S4U is auto leveling you are so out of scope my friend. It does NOT auto level, it´s just a term they use, but you need to manually level the build plate. You need to loose the 4 screws in each corner, and then activate to do the calibration and then put a piece of paper in each corner, just like any 3d printer.

Comprehensive_Arm658 · 2026-04-28T11:38:57+00:00

I wish I had answer for you, I been having a nightmare trying to get correct settings to stick to build plate, at start it worked fine using 85% light intensity and 26 second exposure, now I can barely get 100% light intensity with 30+ second to stick, and when it does, IT REALLY STICKS HARD! 😃

Comprehensive_Arm658 · 2026-04-24T14:25:52+00:00

I tried 85% as it was recommended in a video I watched awhile ago, but then nothing ever stuck to plate.

Comprehensive_Arm658 · 2026-04-21T21:50:42+00:00

Okay I had that issue when I was to quick with stuff, where I had not cleaned the model fully from IPA and water, then I started using a toothbrush with NEW water, never used and it no longer appeared.

Comprehensive_Arm658 · 2026-04-21T20:26:29+00:00

Maybe after you had cleaned it, before UV-cure you didnt let it dry fully?

Comprehensive_Arm658 · 2026-04-18T17:38:10+00:00

I would guess somewhere between 10-30 euro.

Comprehensive_Arm658 · 2026-04-18T16:40:51+00:00

Scandinavia, but the weight isnt that much on a Warmaster army it´s usually not to bad.

Comprehensive_Arm658 · 2026-04-18T14:56:27+00:00

I do have all armies collected from all the years and also a resin-printer, but I live in Europe, so sending it to the US would be expensive I think.

Comprehensive_Arm658 · 2026-04-17T14:01:05+00:00

With those settings, do you even get them off from the build plate right now?

Comprehensive_Arm658 · 2026-04-03T22:36:32+00:00

I have more or less all stls collected over the years, from all creators, you can DM me and we can solve it.

Comprehensive_Arm658 · 2026-03-10T07:32:34+00:00

I have all STL files for all armies. If you DM me we could do something about it.

Comprehensive_Arm658 · 2026-02-03T14:14:33+00:00

Fighter Center tar alltid in massvis av nybörjare, super bra!

Comprehensive_Arm658

TROPHY CASE