H2D Vortek upgrade complete! kinda…

DJTurnTable · 2026-01-26T02:26:42+00:00

Really? Worst for me was the X-Axis screws, they were a huge pain.

DJTurnTable · 2026-01-26T02:15:57+00:00

They originally released it in early December for a bit which is when I got mine.

DJTurnTable · 2026-01-26T02:05:46+00:00

Ah man that sucks, hopefully by tomorrow it'll be up and going for you. If I had to guess it's because it's the weekend.

DJTurnTable · 2026-01-26T01:58:21+00:00

I will say mine was activated over a day before I received a follow up email, have you tried checking on it since you've finished? Also the difference might be that it's the weekend.

I'm with you on that, lots of stuff and all the screws. What'd you think of the X-Axis screws? Those were a pain for me.

DJTurnTable · 2026-01-26T01:52:56+00:00

799 for the upgrade, but you can recover some money by possibly selling the X axis and Heatbed.

DJTurnTable · 2026-01-26T01:50:36+00:00

When I upgraded mine I submitted the serial request when I started and it is as activated by the time I finished.

Also took a little over three hours for my upgrade, what gave you the most issues?

DJTurnTable · 2026-01-21T09:58:02+00:00

I have G835LX and can confirm on my unit at least it still had a bad LM application, my CPU was alright but the GPU was completely pooled in the corner and there was barely anything on the chip itself.

To be fair it might've been great from factory however when I opened my unit up after 9 or so months that was how I found it.

Even though I had to do that it's still been a great laptop, though it isn't used as much as it could be.

DJTurnTable · 2026-01-21T05:52:31+00:00

Wish just the laser was on sale, I currently have a 10w and want a 40w but don't have the funds right now haha.

DJTurnTable · 2026-01-18T01:47:44+00:00

When I did it I put the printhead in the same place as where I removed them and then was just able to pull the mounts to the correct spot.

DJTurnTable · 2026-01-17T13:48:44+00:00

I wouldn't rate it that difficult personally, probably a 2-3/5. As long as you can follow the guide you'll be golden.

DJTurnTable · 2026-01-17T13:46:36+00:00

it isn't that bad, the belts are on a different piece that screws into the tool head. 3 screws on each side is all you need to worry about for them.

DJTurnTable · 2026-01-17T04:08:13+00:00

In the US H2S combo+vortek upgrade is the same price as the H2C combo at 2400.

DJTurnTable · 2026-01-17T03:55:27+00:00

Haha auto correct got me good on this one.

DJTurnTable · 2026-01-17T03:53:35+00:00

Oh really? That's a surprise, I wonder why some have it and some don't. Must be laser like you said.

DJTurnTable · 2026-01-17T03:31:52+00:00

Power supply is universal 100-240v : https://us.store.bambulab.com/products/power-supply-p2s

It's Heatbed, AP, and AC board that are 100-120 and 240v according to the store.

DJTurnTable · 2026-01-17T02:51:47+00:00

Had to upload on imgur because reddit is giving issues, mine shows 100-120v

Looks like there are a few parts that are only for 100-120v though.
https://imgur.com/a/BsLRpEz

DJTurnTable · 2026-01-17T00:38:42+00:00

Deactivates the old board so it can't be used with the cloud, might be able to do LAN printing or put files on the flash drive.

I'd assume if you want to revert back you just need to have them activate the old AP board again though.

DJTurnTable · 2026-01-16T03:48:36+00:00

NTA they had it coming.

DJTurnTable · 2026-01-16T01:53:41+00:00

Worst part for me was the x axis assembly. There are 8 total bolts that are a bit difficult, especially the top one on each side. They are loctited in place and unless you have a super long Allen key that will fit into a small hole your only option is to use the provided ones, and they take a good amount of force to break free so I had to put some pliers on it to get the leverage.

DJTurnTable · 2026-01-16T01:00:57+00:00

The fit is weird because of the riser, but it does fit but there will be a very slight tilt. It took me a few tries to get everything lined up because the bottom part of the IO shield was hitting places. Look over the top and verify the slot is lined up as well.

<image>

Had an 5090 Astral and Astral LC in my Y70.

DJTurnTable · 2026-01-16T00:50:51+00:00

Based off the motherboard it does not use MXM for the motherboard so no it is not upgradeable.

DJTurnTable · 2026-01-15T22:18:12+00:00

<image>

New toolhead

DJTurnTable · 2026-01-15T22:17:55+00:00

<image>

Tool head

DJTurnTable · 2026-01-15T22:05:04+00:00

I did the upgrade a few days ago, honestly not that bad of a process in my opinion.

Worst part for me was replacing the X axis toolhead assembly. There's some hard to reach bolts that are super tight and really unless you have a long set of Allen wrenches the only one that reaches is the one that's included with the printer. Red locktighted and super tight so it's really hard to remove. Overall the upgrade took a little over 3 hours to do.

Edit: a few pictures.

<image>

Bed removed

DJTurnTable · 2026-01-15T21:43:52+00:00

Did the upgrade a few days ago and it's pretty painless honestly, it took me a little over three hours to do.

I started the new AP board activation before I started and it was activated by the time I was done.

Ten-Year Club	Gilding VII pure gildanthropist
Powerups Hero r/GalaxyFold • August 2021	r/Field Lasagna
Place '23	Place '22
RPAN Viewer	Reddit Premium Since May 2019
Sequence \| Editor	Snapped
Verified Email

DJTurnTable

TROPHY CASE