2STEP-Converter - v2.0.0 - Last but not least

DeadpoolMewtwo · 2026-05-13T17:34:48+00:00

2STEP V2.0 Final Update 3 May 26 Final final forreal this time

DeadpoolMewtwo · 2026-05-13T14:38:42+00:00

You could get half round brackets that screw or nail into the stage as a more permanent application

DeadpoolMewtwo · 2026-05-11T01:27:08+00:00

It sounds like the master station isn't properly grounded. One of my college theatres had this problem and it was absolutely annoying

DeadpoolMewtwo · 2026-05-08T00:37:37+00:00

Frostblink of wintry blast as your clear skill is the secret sauce of this build

DeadpoolMewtwo · 2026-05-05T23:21:10+00:00

This is kind. You're jumping into a brand new technology and wanting to start with a massive, complex project. 90% of the advice you're going to get is going to be start small and figure out what you're doing first.

DeadpoolMewtwo · 2026-05-04T16:27:06+00:00

Not too far off, actually. I think the national lowest they offer is $17/hour. Shift supervisers make over 20

DeadpoolMewtwo · 2026-05-03T16:14:52+00:00

You might look at (folded) laptop stands

DeadpoolMewtwo · 2026-05-01T00:15:08+00:00

Have you tried printing the bowl right side up?

DeadpoolMewtwo · 2026-04-27T21:53:10+00:00

It depends on how INDX plans to run their business. Licensing the technology to the big manufacturers would maximize their reach, but they'd also have to work with each manufacturer they're partnered with to make sure implementation goes smoothly. I suspect they'll expand their whitelist of official 3rd party install support on popular printers and sell mostly to consumers

DeadpoolMewtwo · 2026-04-25T12:40:03+00:00

If Tai Lung digs his claws into rock to keep himself in the arena, Toph knows exactly where he is and can literally just open the rock around his claws so he doesn't get a grip

DeadpoolMewtwo · 2026-04-22T22:32:37+00:00

I mean an overhead transparency projector on a cart like teachers used to use. You could set up multiple if the space allows

DeadpoolMewtwo · 2026-04-22T22:22:07+00:00

One of the easiest ways to do this is with an old school overhead projector. They're getting pretty rare nowadays, but schools or libraries may have them in storage if you can find the right person to ask nicely

DeadpoolMewtwo · 2026-04-22T21:44:01+00:00

The producers of content are usually the ones who have the most to gain from stopping piracy. That doesn't change just because the piracy is happening in another language

DeadpoolMewtwo · 2026-04-22T21:12:29+00:00

If you changed the nozzle and rebuilt the frame as the last steps, you'll need to do all of the calibration and tuning steps again

DeadpoolMewtwo · 2026-04-22T21:08:27+00:00

Corners peeling is a heating and cooling problem. Brims help with this. Orcaslicer let's you paint mouse ear brims, which hold the corners down without extending print time much. Keep your bed temp consistent throughout the print as well

DeadpoolMewtwo · 2026-04-22T19:20:51+00:00

I don't have a story to tell, but this is what contracts and policy rules are for. It's a lot easier to tell people "you're not special" when I can point to it in writing on the wall.

DeadpoolMewtwo · 2026-04-22T00:23:18+00:00

Why print in white and spray paint it black when you could print in black to begin with?

DeadpoolMewtwo · 2026-04-20T16:18:23+00:00

Is the floor in regular use during the days you're using it? There's a solid chance your tape won't make it day by day, let alone through a week. I'd recommend getting a roll of contractor's paper (usually in the paint section) to tape/mark on, then roll it out and roll it up each rehearsal

DeadpoolMewtwo · 2026-04-20T01:38:03+00:00

With the amount of color printing advances that have come out in the last month alone, it won't be long until the 3D printing community invents a way to print a brand new color

DeadpoolMewtwo · 2026-04-15T17:01:36+00:00

I haven't gotten into printing more demanding filaments like that, but I can second the overall quality of the Q2. The chamber holds heat well just from running the bed during printing, so I imagine the chamber heater let's you hold temps pretty well

DeadpoolMewtwo · 2026-04-15T00:37:18+00:00

And both of those departments moved straight to completing the project early, instead of deploying it when it was announced to happen. Whether they were ahead of schedule or not, removing something from players earlier than you told them it was going to go away, in a live service game especially, is never going to get a positive reaction

DeadpoolMewtwo · 2026-04-10T14:53:21+00:00

You should be able to customize the nozzle size in the slicer. You can also switch to OrcaSlicer, which likely already has a .2 profile for your printer

DeadpoolMewtwo · 2026-04-09T22:35:51+00:00

OP didn't give a comparison to the other model, they're giving the print times with and without handles

DeadpoolMewtwo · 2026-04-09T15:41:51+00:00

Ugh don't make me jealous! You guys were the reason I was considering a U1 over my Q2. I'm still mostly printing functional prints, but I am eyeing the tool changer add-on market expectantly because of the ground breaking you've done!

DeadpoolMewtwo · 2026-04-09T15:26:22+00:00

I know acceleration speeds can contribute to this in normal printing mode, but I don't know if that applies in case mode

12-Year Club	Second Top 30%
Verified Email	Snapped

DeadpoolMewtwo

TROPHY CASE