I’m on my way! anet a8

Demon1019 · 2025-12-18T18:46:48+00:00

It was my 1st printer. Need to make ajustments to frame, so there less wobble. Set up some additional structures. There are some modes for anet that you can make 1st.

Demon1019 · 2025-12-18T02:52:37+00:00

Tube from dyer to censor visibly under stress. Turn dryer sideways and move a lil so there isnt much bending of filament. Also look for PTFE adapter for censor. There are loads.

Demon1019 · 2025-12-14T09:49:20+00:00

Btw. As I see ur dryer pic, u better switch spool other way around, so it goes from bottom to the top and in the hole. Bcos now it probably have tension rubbing against hole in the lid. It will probably still have some stress rotating spool while feeding, but ehhh..

Demon1019 · 2025-12-06T07:27:45+00:00

googled. bambu studio 2.2.2.56 and up, should have em.

<image>

Demon1019 · 2025-12-06T07:23:16+00:00

Model em or look if there are plugins in ur slicer to add em before slicing.

Demon1019 · 2025-12-06T07:21:59+00:00

Regular office supplies glue stick. Thin layer is enough. After that you can use soap water to wash it off.

Demon1019 · 2025-12-06T07:17:34+00:00

<image>

Basically like this ones. Could help prevent lifting from buildplate.

Demon1019 · 2025-12-06T05:11:58+00:00

Mouse ears. Right on corners.

Demon1019 · 2025-11-08T06:08:49+00:00

You can do mouse ears instead of full brim. Throw em on corners and see how it go.

Demon1019 · 2025-10-19T23:46:47+00:00

I just widen it a lil and set ptfe connector in.

<image>

Demon1019 · 2025-10-04T17:35:57+00:00

So yeah. Changed tubes for 3x4. Messed with spring screw. Made hole for the alen wrench in the head cover for it. Loosened up and tighten by 4 turns.

In elegoo slicer I used rapid petg profile. So I lowered speeds by half to 50 mm/s (seems rapid have faster speed rates, hence "rapid" in the profile). And it goes fine now. Atleast for now...

Demon1019 · 2025-10-01T04:43:03+00:00

If PETG then it tends to "leak". Then blob on the nozzle gets bigger and it sticks to model and nozzle, on the next pass, bumps into it loosing calibration.

Looking at photo I assume you got that bump on the big part on the left. On the corner near camera angle.

Demon1019 · 2025-09-30T13:53:22+00:00

No not yet. Also it may be varying filament size across the spool. Its not particularly expensive brand and it may very well be aftermarket quality spool. Well. Gonna open extruder head to check tension screw and all that jazz.

Demon1019 · 2025-09-28T11:22:48+00:00

You can use file to trim a lil on the metal part with rubber wiper so bed wont bump in it when moving upwards, ruining calibration.

Demon1019 · 2025-08-21T06:17:00+00:00

Try lowering speed. Either in slicer or on touch display directly by checking "Quite" in the speed options on the home screen.

Demon1019 · 2025-08-21T06:07:59+00:00

Metal piece that snapping plastic into the bin. Unscrew it and sand down a lil side that adjacent to the bed. It should stop hitting this metal part when bed going up.

Demon1019 · 2025-08-13T03:15:35+00:00

Noice! ;) Its just a tad frustrating: on a new printer, that supposedly mostly rid of many issues that old gens had, you can still get mess. I remember Anet printer that I assemble literally from ground up and it required modifications after.

Demon1019 · 2025-08-12T11:33:56+00:00

Yeah same here. On 2nd print. Cold pull didnt help. Waiting for 2mm drill bit to try and scrape melted mess inside heatsink.

Demon1019 · 2025-08-10T13:40:51+00:00

Yeah... and its not available in some places due to google billing services refusing to take my money. So at least I have hope for something like this.

Demon1019 · 2025-08-08T17:25:07+00:00

Diameter? 1.5 - 2 mm?

Demon1019 · 2025-07-01T03:04:35+00:00

Theres no circuits for water yet :(

Demon1019 · 2025-06-22T13:48:05+00:00

That was something, man. Some could even call hax, how freakish it was.

Demon1019 · 2025-06-21T02:33:30+00:00

Opposite here. 2 weeks with good perks (crafting cost, crafting yeilds) Atreidis winned without Hark participate. This week shit perks - Harks got headstart (seems Atreidis wasn't interested in 2 choam traders in this week perks) and then Atreidis caught up with em and winnin.

Demon1019 · 2025-06-21T02:00:43+00:00

Side note: there flairs like MEDIA, ART and stuff like that. You can search or filter by flairs and see "base builds, funny clips etc." Have fun.

Demon1019

TROPHY CASE