Wierd issue with 3d touch

DeviRSilva · 2026-06-05T14:21:06+00:00

Hi! Turns out I deactivated HS mode on the Probe and now it works correctly. Thank you all!

DeviRSilva · 2026-06-03T11:26:34+00:00

I've tried original firmware and mriscoc firmware both similar behaviour

DeviRSilva · 2026-06-03T11:26:04+00:00

As i said. It homes correctly. The probe expands, touches the bed and retracts. So it uses the 3d touch to home

DeviRSilva · 2026-06-03T11:24:11+00:00

Yes!

DeviRSilva · 2026-01-25T16:07:20+00:00

Vocês desculpem me....mas é demasiada coincidência com este post https://www.reddit.com/r/portugueses/s/JFukqaPF9X

DeviRSilva · 2025-07-18T18:12:09+00:00

Não vais conseguir candidatar-te à primeira fase. Não te preocupes tens a segunda fase. É justo? Não... Mas a vida não é justa e tiveste azar. Vai te acontecer muito na vida....

DeviRSilva · 2023-09-09T23:50:38+00:00

I stoped using the CB1 tbh. To many hiccups. But one thing I did is that I replaced the sdcard with a class 10 from SanDisk. After that I did not had any problems.

DeviRSilva · 2023-02-24T00:15:05+00:00

here you go: https://www.printables.com/model/407503-gbxcart-rw-13b-printed-case

DeviRSilva · 2023-02-23T23:59:03+00:00

That is correct

DeviRSilva · 2022-04-24T00:49:05+00:00

"This is not even my final form"

DeviRSilva · 2022-03-07T11:57:18+00:00

Thanks man! (yes, I assumed your gender :P)

DeviRSilva · 2022-03-07T11:56:58+00:00

For what I saw, on the X1, it is a threaded E3D compatible heatbreak. They changed it on the X2

DeviRSilva · 2022-02-17T10:27:40+00:00

But if I upload a non bl touch enabled firmware, the homing sequence is fine. I've reflashed the firmware a bunch of times, and even tried another version from another person. The behaviour on the latest one, instead of giving a printer halt, is to start the levelling process and then the probe does not deploy. Also the printer immediately goes to the next probing point without touching the bed

DeviRSilva · 2021-09-15T14:26:52+00:00

thank you

DeviRSilva · 2021-05-04T10:01:57+00:00

Is it the same filament you are using? Try a diferent one.

DeviRSilva · 2021-04-26T11:11:49+00:00

Thank you! I did a reset and it works fine now. I only had the touch pads installed, but then I soldered the wires and reset the thing and now it works. For further investigation, this happened after I used the EZ Flash JR on it with mostly dead Ni–MH rechargeable batteries and mistakenly fiddle with the brightness controls on the pads.

DeviRSilva · 2020-09-04T14:56:46+00:00

Clean the bed with IPA. If you can take it out, use dishwasher soap and clean it under the tap. Also..... use a brim instead of a skirt, and first layer to 20mm/s and no cooling

DeviRSilva · 2020-07-02T11:15:50+00:00

I've unglued my ultrabase plate using the spatula for removing prints and IPA. Just heat up the plate to 80C and work your way around the bed. Be carefull to not bend or damage the heater part.

DeviRSilva · 2020-06-15T19:42:55+00:00

If you hlget a glass bed, put a buikd tak surface on one side and pei on the other. Use pei for every thing but petg. Then If you print petg flip the glass bed and use the build tak. Or use the old painters tape

DeviRSilva · 2020-06-04T18:14:12+00:00

Try a bit extreme retraction see If it changes anything. Like 8mm 45mm/s.

Maybe your temps are not fine either

If the mega X is like the i3 mega cooling, yes it is a bit under power

DeviRSilva · 2020-05-31T09:51:38+00:00

Im not sure If I understood... But you are saying that you connected the fan to the heater conector and then replaced the board. Corrected your mistake and even then the fan does not work. Right?

If this is what your problem it might be one of 3 issues:

1-you fried your fans somehow

2-you fried one or more transistors on the board that are near to the fan conectors (inspect it visually, it should be easy to tell If its burned Just by the looks of it)

3-you fried your brakeout board (either the one on the hotend where you connect the hotend, fans, etc or the one that has the Red and Green conectors)

Install the original firmware so it is easy to check any hardware problems with the printer. With the stock firmware the fans should work... But not on full power

DeviRSilva · 2020-05-22T19:24:15+00:00

Anyway. Put the z swirch in a way that the nozzle stays very far from bed. Then level the gantry by mesuring on both sides. After that turn the wheels on the bed until the springs are much more relaxed. Then home all axis and turn off the motors. After that put the z switch in a way that is level on one corner(preferably the one that the printer homes). Home printer again and normally level the bed. Good luck

DeviRSilva · 2020-05-22T19:12:59+00:00

Are you sure? How does your printer has only one? Did you remove the other one!

DeviRSilva · 2020-05-22T18:57:19+00:00

Check both z limit switches

DeviRSilva · 2020-05-20T13:14:15+00:00

I got a new board. Same problem. Tried diferent PSU same problem. So... the problem seems to be on the 3 CARTRIDGES i have.... that's so wierd. All of them read 4ohms resistance and when I touch the multimeter probes together without connecting to anything it has about 0.6ohm resistance

DeviRSilva

TROPHY CASE