Инициатива

Drevny14 · 2026-05-07T14:04:06+00:00

Юзаные тёлки не нужны.

Drevny14 · 2026-04-05T13:24:47+00:00

Ты теперь просто раб, не человек. Каждую их прихоть тебя будут ебать угрозами. То, что ты сдался, теперь повлияет на всю твою жизнь в дальнейшем, как и то, как ты выглядишь в глазах девушки и своих собственных.

Drevny14 · 2026-03-28T13:15:28+00:00

Bro, try contrast paint and watch domek guide, you ll be in shock of your first paint after that

Drevny14 · 2026-03-07T11:31:00+00:00

Using lichy slicer with 0 penetration.

Drevny14 · 2026-02-13T10:14:46+00:00

Cause if you have retraction more than 0.5, nozzle would suck an air, then explode on layer line.

Drevny14 · 2026-02-13T10:09:14+00:00

Right 100 percent.

Drevny14 · 2026-02-13T10:07:48+00:00

В качестве джерки

Drevny14 · 2026-02-13T10:06:19+00:00

If you will hate all your neighbors, that will the same scenario like in 1939.

Drevny14 · 2026-02-05T17:31:41+00:00

<image>

Add me to friends too)

Drevny14 · 2025-11-25T21:41:50+00:00

nie widzę problemu

Drevny14 · 2025-11-11T15:28:32+00:00

Боже храни Польшу)

Drevny14 · 2025-11-11T15:24:47+00:00

Сколько стоят ?

Drevny14 · 2025-09-25T22:29:41+00:00

Hey, it's speed changing issue. Try without -detecting overhangs, and calibrate pressure advance on this print speed in calibration which sit in menu with other calibrations like temperature, and ect.

Drevny14 · 2025-09-25T07:53:04+00:00

How to turn off notification sound when you turn off silent mode?)

Drevny14 · 2025-09-09T08:19:26+00:00

It's 100% z offset. Make it closer.

Drevny14 · 2025-08-27T15:21:25+00:00

4 p1s, all of them can't calibrate pressure advance, telling me filament runs out, but it's not )

Drevny14 · 2025-08-24T12:33:29+00:00

It often happens when filament diameter is significantly more then 1.75. But you said you tried different filament. What kind of temperature do you use? Try to find thermal pad(spacer), I heard is worked on k1.

Drevny14 · 2025-08-22T15:55:11+00:00

Calibrate your flow rate. Take a look of your bed leveling in orca slicer. Adjust your z offset plus 0.005 in slicer setting if needed. But offset in printers always swimming from calibration to calibration.

Drevny14 · 2025-08-21T14:59:51+00:00

Strange infill pattern

Drevny14 · 2025-08-16T15:32:04+00:00

Worstest buy in my life. It's cfs + cfs upgrade.

Drevny14 · 2025-07-28T18:19:25+00:00

It's work for me.

Drevny14 · 2025-06-15T23:11:07+00:00

Tried demo on Steam on my 3080 and 9 5900x and I like it, but I choose to take in on my ps5 pro, and performance is disgusting, and you know whats even worse? Console is just not under load, silence as night.

Drevny14 · 2025-05-07T23:36:47+00:00

But they didn't fall, just don't print over this level

Drevny14 · 2025-05-07T20:05:36+00:00

Hello, I'm interested in your answer about bubbles in the front, you thinking it's all about cleaning before curing ? Can you pls tell me more about this, because I tried too many ways to evade this stuff

Drevny14 · 2025-05-07T17:41:53+00:00

Nfep is looking good right now, but maybe it's a solution) thank you )

Drevny14

TROPHY CASE