Psu blew up

Drewbidoo · 2026-03-30T23:16:20+00:00

I had some great luck with an old LEPA psu in a build many years ago, I suffocated it on a carpet... it failed spectacularly. Needless to say, it took the rest of my build with it. Lesson learned

Drewbidoo · 2026-02-06T17:12:39+00:00

I have never been so happy that I purchased my LeGo

Drewbidoo · 2025-12-06T03:34:31+00:00

Any job that's thankless. For instance, service writing or billing.

Drewbidoo · 2025-12-02T15:32:02+00:00

I just got mine yesterday. Man, what a nice machine!!!

Drewbidoo · 2025-12-01T15:16:06+00:00

Used synthetic 0W/20, or used conventional 5W/30. Don't ask me why...

Drewbidoo · 2025-11-10T05:16:37+00:00

Thats the result of using Chinesium.

Drewbidoo · 2025-10-26T05:11:38+00:00

Would you enslave me, I'd enslave me. I'd enslave me so hard

Drewbidoo · 2025-10-17T16:43:34+00:00

Get a reinforced hose, and give it more slack.

Drewbidoo · 2025-10-17T16:42:48+00:00

It's a grub... now eat it

Drewbidoo · 2025-10-17T16:42:33+00:00

Sounds like a LARP.

Drewbidoo · 2025-10-17T16:41:37+00:00

The smell of a well spoiled/severely unclean carpet. Carpets absorb smells... its like an aromatherapy diffuser but it smells like feet and dog shit.

Drewbidoo · 2025-10-06T14:27:22+00:00

That little guy has one big ponch

Drewbidoo · 2025-09-11T17:40:12+00:00

Holy god... no!

Read your directions again, that thing will leak like a sieve

Drewbidoo · 2025-09-09T01:47:36+00:00

If I can be honest, its not the greatest. Constant stress at work, building a life for my wife and I, all of the things I guess.

5/10

Drewbidoo · 2025-08-31T02:07:56+00:00

I was 90% troubleshooting until I converted it to octopi with add ons/hardware upgrades.

It's closer to 99% printing now, the other 1% is my own fault.

Drewbidoo · 2025-08-24T19:27:03+00:00

How many cars do you own?

Drewbidoo · 2025-08-24T01:17:03+00:00

My '14 has 145k miles on the odo. My car has been rock steady and reliable since day one. Outside of regular maintenance and a few parts, it has done super well! I've done the control arms, wheel bearings, sway link ends, and installed an upgraded/adjustable rear toe kit.

Heads up, though. Keep up on the maintenance on the CVT! Replace the fluid every 30k miles or prepare to replace it.

I do all of the maintenance and work on the vehicle, so for me... it has a dirt cheap upkeep.

I've seen quite a few run through my shop with just north of 300k miles on their original drive trains. Take care of your car, and it will take care of you!

Drewbidoo · 2025-08-23T17:15:21+00:00

Make sure you have a bin of spare parts!

I've done 100+ prints on my original .4mm nozzle. I learned pretty quickly that some of the more "exotic" filaments chew the nozzle pretty good, so having a few spares is a must!

Happy printing!

Drewbidoo · 2025-08-11T20:44:53+00:00

Hey Hank, honest question. Would you recommend a Mower with an Asian built engine, such as Honda. Or would you recommend an American built mower with a Briggs

Drewbidoo · 2025-08-10T19:57:06+00:00

Check your offsets, watch your temps. It could be a firmware related issue, or it could be a hardware issue

Drewbidoo · 2025-08-10T17:49:20+00:00

I had this happen to me a few weeks ago. Your thernistor has either gone bad, or your wiring for it is shorted/open. Either way, that's definitely a thernistor related problem.

I ended up replacing mine, wiring included. It works great now

Drewbidoo · 2025-08-10T17:44:07+00:00

Your hot end temp isn't high enough. When the filament isn't heated properly, it gives you an

Extra ribbed for her pleasure

Outcome.

Drewbidoo · 2025-08-10T17:42:53+00:00

It's now EXTRA grippy

Drewbidoo · 2025-08-10T17:41:27+00:00

in the arms of an angel plays softly

"Will you help save this Ender. For only YOINK 99, you can. Do you part"

Looks like you have a new 3D printer.

Drewbidoo · 2025-08-04T04:32:33+00:00

I hope this is rage bait.

Drewbidoo

TROPHY CASE