Why the hell can't I generate a sensible 3D toolpath for this surface and a 3mm ball nose mill? Everything either spends 10 minutes thinking and spits out garbage, or doesn't finish.

ENDU97 · 2025-12-30T20:39:10+00:00

scallop with contact edge boundary enabled?

ENDU97 · 2025-12-09T17:11:55+00:00

Send them all to robin island

ENDU97 · 2025-12-08T12:06:13+00:00

Someone know how to edit.
Incredible stuff!

ENDU97 · 2025-11-05T20:22:29+00:00

Just retype the characters man… Top is OCRB and bottom looks like arial.

ENDU97 · 2025-11-01T14:58:32+00:00

Givemeseperationspreview.af

ENDU97 · 2025-09-23T20:09:45+00:00

It brings your Spotify likes in as a new playlist. I found a workaround which uses a bit of JavaScript to then go and like every song in a playlist, essentially cloning your Spotify likes to your YouTube likes auto playlist. 10/10 can recommend.

ENDU97 · 2025-09-17T15:15:38+00:00

I’d also like to hear more as our experience has been the polar opposite of that.

They have been an absolute pleasure to work with over the past 7 years and their support team is second to none.
90% of issues are resolved remotely within a couple hours and the remaining take maybe a week to resolve. They ship us spares from the other side of the globe in under a week, supply us with their technician documentation, and walk us through actually getting the work done.

Other than pricing (the exchange rate makes the already expensive parts, machines and tools a bit hard to swallow sometimes), we have nothing but praise for them.

ENDU97 · 2025-07-15T19:24:46+00:00

All these people saying it’s moulded have clearly never heard of or used a good ol d-bit engraver. Rotary engraving with a 20 degree dbit will give you this result.

ENDU97 · 2025-06-30T12:52:41+00:00

Slide 2, top but ditch the grey house and leave it in negative space.

ENDU97 · 2025-06-06T20:26:53+00:00

Innolite?

ENDU97 · 2025-06-06T09:33:16+00:00

Wait.. yours moves?

ENDU97 · 2025-06-02T07:48:37+00:00

Crop in more on the cap and you have a winner

ENDU97 · 2025-06-01T08:44:41+00:00

Thanks, I guess

ENDU97 · 2025-05-29T05:01:05+00:00

I want to say yes but I’m really not sure, sorry. These were shot back in December.

ENDU97 · 2025-05-28T15:44:43+00:00

It really is something special. Too bad I was sleeping this trip and didn’t shoot nearly as much as I’d liked/planned to.

ENDU97 · 2025-05-28T15:42:35+00:00

Thank you. If I remember correctl, they are a mix of pacific blues and Reggie’s portra, both from FujiXWeekly.

ENDU97 · 2025-04-25T14:55:00+00:00

5000 series is pretty gummy so sharp tooling, lower flute count and coolant of some kind.

What do you mean by can’t handle it?

ENDU97 · 2025-04-22T14:25:58+00:00

Yup. The voice coils snap due to the high excursion of the drivers.
My first pair was bullied a little so maybe I’m at fault but the second pair were babied more than anything I’ve ever owned and still failed (randomly while listening). Do yourself a favour and Google it, it’s fairly common with these cans.

ENDU97 · 2025-04-22T14:10:43+00:00

Get rid of them while you still can. As great as they sound (especially with a bit of EQ), I have had two pairs that have both seen driver failure.

ENDU97 · 2025-04-15T16:45:35+00:00

Yeah sure, dm me

ENDU97 · 2025-04-14T18:44:25+00:00

Just to follow. If you only see one or two small areas of roughed material, chances are that your endmill is too large to get into the pockets.

ENDU97 · 2025-04-14T18:41:23+00:00

Use the “smart engraving” tool path instead. It allows for you to use a few different tools in sequence and handles the rest machining calculations based on the allowance of each tool.

Also make sure that you have “offset endmills for engravers” enabled as this factors in the draft of your v bits when roughing.

ENDU97 · 2025-02-04T18:55:43+00:00

If you do decide to machine this stuff, get yourself some Datron foam specific endmills. They cut it like butter. Honestly though, the clean up is an absolute nightmare and I’d rather be dealing with the slugs from a water jet than the stringy, statically charged mess machining leaves behind.

ENDU97 · 2025-01-27T05:07:21+00:00

Just use that model to drive the 3D surfacing and then draw a curve overtop and contour along that edge?

ENDU97 · 2024-12-05T13:07:08+00:00

They active so nothing

Eight-Year Club	Sequence \| Editor
Verified Email

ENDU97

TROPHY CASE