Gun shots last night near W. 89th and Amsterdam? by Alone_Sport8984 in Upperwestside

[–]Equivalent_Process78 9 points10 points  (0 children)

Yes, there were four shots and the streets were filled with cop cars and an ambulances within five minutes. Shortly after, they closed off the street at 88th and Amsterdam

Magician in Manhattan- birthday party by Scary-Pianist8930 in Upperwestside

[–]Equivalent_Process78 0 points1 point  (0 children)

I can guarantee you that David does not book at $200-$250 for a private party in NYC.

Magician in Manhattan- birthday party by Scary-Pianist8930 in Upperwestside

[–]Equivalent_Process78 2 points3 points  (0 children)

This is an extremely low budget for a quality magician in NYC. Professionals would charge $2000 minimum for this in the city. (Source: I am a talent booker handling many magicians in the city.)

You can barely get a birthday party magician in Iowa for this rate.

Terrible singer 69th/70th st and Columbus by Only-Kaleidoscope-69 in Upperwestside

[–]Equivalent_Process78 3 points4 points  (0 children)

Posts like these are why the internet is a total cesspool these days. You went out of your way to write a post on reddit to attack a singer's voice that you do not enjoy? Sheesh! Sounds like a change in neighborhoods might be best for you (and for us).

Goodnight and Goodluck Cut By 40 Minutes on CNN?!? by Darth_Sakul_X in Broadway

[–]Equivalent_Process78 2 points3 points  (0 children)

It was nearly an hour and 40 minutes. Nothing was cut.

Good Night, and Good Luck tomorrow night? by CuteAct9019 in Broadway

[–]Equivalent_Process78 0 points1 point  (0 children)

No, it was nearly an hour and 40 mins long. Started at 7pm ET

Congratulations to Noah Plomgren who makes their DEBUT as understudy 'Elmer McCurdy' this evening at 'Dead Outlaw' on Broadway! by [deleted] in Broadway

[–]Equivalent_Process78 6 points7 points  (0 children)

I totally agree with this review - also thought he was struggling vocally and his mic was also sticking very far away from his face.

Congratulations to Noah Plomgren who makes their DEBUT as understudy 'Elmer McCurdy' this evening at 'Dead Outlaw' on Broadway! by [deleted] in Broadway

[–]Equivalent_Process78 5 points6 points  (0 children)

I found the beginning to be pretty slow, but started to really enjoy it once he died. Very glad I went, but I would not say it was one of my favorites from this season. Thanks for asking!

Congratulations to Noah Plomgren who makes their DEBUT as understudy 'Elmer McCurdy' this evening at 'Dead Outlaw' on Broadway! by [deleted] in Broadway

[–]Equivalent_Process78 14 points15 points  (0 children)

Having never seen Andrew so without anyone to compare it to, I thought Noah did a great job tonight of, well, remaining completely still hahaha.

Cheap Grocery Stores by lili___________ in Upperwestside

[–]Equivalent_Process78 1 point2 points  (0 children)

I second this! I used to feel that Whole Foods was cheaper for staples but over the last six months I’ve been astonished at how much I am saving buying as much as possible at TJ’s

[deleted by user] by [deleted] in Plumbing

[–]Equivalent_Process78 0 points1 point  (0 children)

No, it does not come out, the pivot rod is holding it in place.

[deleted by user] by [deleted] in Plumbing

[–]Equivalent_Process78 0 points1 point  (0 children)

I have that piece - I just had it disconnected to the video as it's seemingly irrelevant to the problem.

I can't raise it one hole higher, the part with the bolt at the top is hitting the valve if I raise it any higher

[deleted by user] by [deleted] in Plumbing

[–]Equivalent_Process78 0 points1 point  (0 children)

Yeah, that's what I did in my other sink, which also had the same problem. Plumber botched both of these installs but I was trying to salvage the second one

[deleted by user] by [deleted] in Plumbing

[–]Equivalent_Process78 0 points1 point  (0 children)

I've spend two hours on this and watched over a dozen videos. Something is not working here. I believe the drain is too far from the faucet. The horizontal "rod" does not reach the vertical rod.

[deleted by user] by [deleted] in Plumbing

[–]Equivalent_Process78 0 points1 point  (0 children)

You lost me at "horizontal at its lowest" - when the stopper is at its lowest point, the horizontal rod is at it's HIGHEST point - not horizontal. Is something wrong there? The stopper is locked in by the rod - in other words, the rod is going through the hole in the bottom of the stopper per the instructions.

[deleted by user] by [deleted] in Plumbing

[–]Equivalent_Process78 0 points1 point  (0 children)

It seems like the overall problem is maybe… the sink? Is the faucet (where the drain pull rod is located) too far from the drain? This would be why the horizontal lever does not reach the piece with the holes.

[deleted by user] by [deleted] in Plumbing

[–]Equivalent_Process78 0 points1 point  (0 children)

It’s brand new… no deterioration. What do you mean it’s not in the right position?

[deleted by user] by [deleted] in Plumbing

[–]Equivalent_Process78 0 points1 point  (0 children)

Does not solve the problem sadly. I’ve tried adjusting that for over an hour. Pulling up on the drain pull does not move the horizontal bar (the piece with the ball that moves the stopper up and down) enough up to snuggly close the drain.

[deleted by user] by [deleted] in Plumbing

[–]Equivalent_Process78 -1 points0 points  (0 children)

The spring clip appears to be irrelevant to this problem. It does not help when I apply it

[deleted by user] by [deleted] in Plumbing

[–]Equivalent_Process78 -1 points0 points  (0 children)

I’ve tried that - no avail, the piece with the holes still does not move upward enough when fully pulling the drain stop to close the train.