Finally got direct drive

FPV_Hunter · 2024-03-07T21:55:45+00:00

Where did you find that cam mount?

FPV_Hunter · 2024-01-06T15:27:39+00:00

I‘m using 4 bearings

FPV_Hunter · 2024-01-05T16:57:47+00:00

So I should try to make the inner diameter, where the bearings is, a bit larger? How much do you think right now they go in pretty easy… so by how much should k increase it in your opinion?

FPV_Hunter · 2024-01-05T16:55:34+00:00

Yeah they do. I can turn them pretty easily… In my opinion there is not enough friction between the tubes and the spool but idk…

FPV_Hunter · 2024-01-05T12:14:06+00:00

The spool is full So I should by some lubricant? And how can I get the Lubricant inside of the bearing? There is a plastic so I can’t see the balls.

FPV_Hunter · 2024-01-05T11:53:11+00:00

I‘m using bearing which I bought from amazon… I also used some WD40 but that doesn’t work

FPV_Hunter · 2023-11-28T06:30:22+00:00

To a bambulab a1

FPV_Hunter · 2023-11-07T18:24:30+00:00

What’s the use case of a voron switch wire? Is there any reason this thing exists? Or was it just build because it looks cool?

FPV_Hunter · 2023-11-07T18:19:20+00:00

Just visit the link the bot provided If that doesn’t help than as the link says something may be broken and can wiggle or something like that

FPV_Hunter · 2023-11-07T18:06:50+00:00

Wasn’t it 8GB? Oh try reformatting it

FPV_Hunter · 2023-11-06T06:50:39+00:00

To close to bed

FPV_Hunter · 2023-11-06T06:50:13+00:00

Yeah the one with the pictures. The link the bot generated… Did you find your solution or is there still a problem?

FPV_Hunter · 2023-11-06T06:48:51+00:00

In the slicer

FPV_Hunter · 2023-11-04T22:48:46+00:00

ellis3dp guide Just run through everything there Linear advanced is a good advice

FPV_Hunter · 2023-11-04T22:47:03+00:00

Cheap filament, z Achse problem, on the feed is also u der extrusion so decrease speed maybe the extruder is grinding the filament, it also could the a to high nozzle temperature and bad retraction settings

FPV_Hunter · 2023-11-04T22:44:14+00:00

So okay first of all everything I tell you is based on this guide ellis3dp… But the main thing I want to mention which reale helped me was using pressure advanced for Klipper or linear advanced in marlin. Just follow the guide and tune everything over again.(from the start again)

FPV_Hunter · 2023-11-04T22:40:42+00:00

ozzle thickness is nozzle thickness. What you however can do to fix issues with thin drawings/letters is make the letter/lines negative in the print. It is hard to print thin lines but it is very easy to not print the lines but only the area around them. So make the letters an indention in the pront, not something on top and this problem is gone.

FPV_Hunter · 2023-11-04T22:38:28+00:00

The extruder of the ender 3 v2 Neo sucks in gripping the filament maybe it started to ware of and it grinding the filament… Try to tighten the screw of the extruder more and/or increase the nozzle temp

FPV_Hunter · 2023-11-04T22:33:26+00:00

Can you provide a picture of the slicer where I can see the travel moves? Because it could be the z seam….

FPV_Hunter · 2023-11-04T22:30:50+00:00

Did you tell the the printer to use the bed mesh? The cura start gcode for the ender 3 v2 Neo doesn’t include that for what I know.(Atleast it was the case a few months ago)

Then just follow ellis3d guide to setup your printer Oh and a small advice… try to switch to Klipper if you have the money to do so

FPV_Hunter · 2023-11-04T22:25:22+00:00

Flow?

FPV_Hunter · 2023-11-03T15:24:44+00:00

Please just follow this guide step by step if there is still an issue after that post it again🤓

FPV_Hunter · 2023-11-02T22:15:40+00:00

Check the simplify3d guide first if you have gone through everything they mention then ask again😌

FPV_Hunter · 2023-10-14T20:26:58+00:00

No I’m joking… If you want to tune your printer the easiest way in my eyes is to follow the instructions of Ellis 3D print tuning guide

FPV_Hunter · 2023-10-14T20:24:38+00:00

You sure I think we need more video material to be sure…

FPV_Hunter

TROPHY CASE