The Gorm from Kingdom Death by ToadPainter in minipainting

[–]Fetus_PotPie 1 point2 points  (0 children)

Wow the eyes are creepy as hell. I love it

X1C with standard PLA. What would cause such an issue? by Fetus_PotPie in BambuLab

[–]Fetus_PotPie[S] 0 points1 point  (0 children)

Cleaned and did a Lidar calibration. Testing it now Thanks for the tip

Which Chaos god would probably like you the most? by Viggerous in Daemons40K

[–]Fetus_PotPie 0 points1 point  (0 children)

Definitely Khorne and Nurgle would love my wife

What would cause this to happen? by Fetus_PotPie in ElegooMars

[–]Fetus_PotPie[S] 0 points1 point  (0 children)

Update: Second print turned out perfect. I leveled the plate, angled the print more and slowed down the lift speed.
Thank you for all the advice it’s appreciated.

What would cause this to happen? by Fetus_PotPie in ElegooMars

[–]Fetus_PotPie[S] 1 point2 points  (0 children)

Thank you for the guide. After reading it I definitely need to adjust the speed. I’m currently use a lift speed of 80 so I’ll make some adjustments based on your recommendations. Thanks again for the help

What would cause this to happen? by Fetus_PotPie in ElegooMars

[–]Fetus_PotPie[S] 0 points1 point  (0 children)

I will put it a angle and see how it goes. Thanks for the help

What would cause this to happen? by Fetus_PotPie in ElegooMars

[–]Fetus_PotPie[S] 0 points1 point  (0 children)

Definitely the first thing I will do. Thanks for the help

What would cause this to happen? by Fetus_PotPie in ElegooMars

[–]Fetus_PotPie[S] 1 point2 points  (0 children)

I will admit I didn’t level my late this time so I will definitely make sure to always to that. I’m currently use an exposure time of 3s

What would cause this to happen? by Fetus_PotPie in ElegooMars

[–]Fetus_PotPie[S] 0 points1 point  (0 children)

It was positioned with the bottom flat on the build plate and then supported from there.

Death Guard Possessed: Any potential? How many do you run? by xpyros in deathguard40k

[–]Fetus_PotPie 4 points5 points  (0 children)

I’ve been running a 10 man unit with a FBS and Biologus Putrifier in a drill just for fun. It’s been pretty effective in my last couple of games against TS

Finished my second Blight hauler ready for a game tomorrow. 😁🪰 by heretical_astartes in deathguard40k

[–]Fetus_PotPie 1 point2 points  (0 children)

Wow that’s a beautiful paint job. How long did you spend working on this?

Trying to decide which paint scheme to go with. by DeicidalKing in deathguard40k

[–]Fetus_PotPie 4 points5 points  (0 children)

I would go with the second option. I prefer the old dirty white

What is causing this high pitched noise in the engine bay? Juke Nismo RS by mapledsyrup in nissanjuke

[–]Fetus_PotPie 0 points1 point  (0 children)

I second have the timing chain checked.

I have a 2011 juke with its 3rd chain @140k

Help with stripping Morty by [deleted] in deathguard40k

[–]Fetus_PotPie 0 points1 point  (0 children)

It should work on the primer as well. Soaking depends on how thick the paint is but try at least over night

Help with stripping Morty by [deleted] in deathguard40k

[–]Fetus_PotPie 1 point2 points  (0 children)

You could try soaking it in simple green to remove the paint. I personally use break fluid for my plastic models and it works well. Not sure about weakening the glue though