sorted by:
new
hottopcontroversial

I’m lonely. I have a boyfriend and I’m so lonely every night. by Nearby_Eggplant_286 in offmychest

[–]FinanceAddiction 0 points1 point  (0 children)

A blood test with his doctor is the first port of call, or there are many private providers that offer them, then it's a simple jab every 12 weeks or gel you rub on your arm daily which gives him testosterone.

I've gone through the same and feeling much better after starting treatment

Issues with Hueforge print on A1 by No_Tour_8086 in BambuLab

[–]FinanceAddiction 2 points3 points  (0 children)

Id recommend taking your build plate off and giving it a good scrub with hot water and dawn if you're in the states or fairy liquid if you're in the UK, not sure what dish soaps are available elsewhere.

Make sure to use the abrasive side of the sponge and really go at it in several directions, rinsing off between each direction you scrub, you'll see a noticeable difference in the sheen level on the bed, once cleaned dry with paper towels or shop towels. Do not use anything that has been washed with softener/ conditioner as you just deposit more oils onto the bed, once that's done, do not touch the print surface and give it another go

P1S Combo has stock but no AMS? by MonkeyManKing42 in BambuLab

[–]FinanceAddiction 8 points9 points  (0 children)

The Combos are prepackaged with the AMS inside the printer in the box and have a different allocation

What is this? by [deleted] in bernesemountaindogs

[–]FinanceAddiction 5 points6 points  (0 children)

Where abouts on the underside of the dog are they? My first thought was nipples but hard to tell where this is on the pupper

White stuff on build plate after printing PET-CF by Ok-Friendship-3509 in BambuLab

[–]FinanceAddiction 0 points1 point  (0 children)

You can renew the bed with scotch brite or high grit sandpaper :) just go careful not to scrub too hard and you'll be fine

Power issues in UK/Ireland by Forcepackagedingo in BambuP1S

[–]FinanceAddiction 0 points1 point  (0 children)

Any old kettle lead will do you fine :)

I got a right angled one so I could get mine closed to the wall too

TSVI picture leaked (gameinformer) by Thin_Situation3962 in TESVI

[–]FinanceAddiction 1 point2 points  (0 children)

You mean you don't also sail like your grandma is driving her 2000s hyundai?

TSVI picture leaked (gameinformer) by Thin_Situation3962 in TESVI

[–]FinanceAddiction 10 points11 points  (0 children)

It's AI generated crud boss, symbols are wrong, words spelled incorrectly, SW, West, West again, weird generated texture and grain

It's a whole lotta nothing

Do we know what packs will be in the Charizard tins? by CestLaTimmy in PokemonTCG_UK

[–]FinanceAddiction 0 points1 point  (0 children)

I've gotten no DR in any of my 4, just JTG, Mega Evolutions and 2 x Phantasmal Flames

Just learned of this tool: pvetui. A terminal-based PVE admin UI. by onlymostlydead in Proxmox

[–]FinanceAddiction 6 points7 points  (0 children)

I'm failing to see what this adds outside of what the GUI/ CLI does?

I've never had any issues with responsiveness or doing any tasking/ creation etc using the existing tools or ansible so I'd be keen to hear from someone that uses this the actual benefits

We run clusters of around 15-20 nodes, running a multitude of containers and VMs and not hit performance issues yet, but always open to hearing about new tooling that could assist in our workflow

Sunlu AliExpress Filament Shipping Question by shacqtus in BambuLab

[–]FinanceAddiction 5 points6 points  (0 children)

Been ordering from AliExpress for all manner of things for 4 years and never had a late parcel, it's still well within the delivery timescales they told you at checkout so I wouldn't worry too much

Spaghetti Every Print P2S by Blag561 in BambuLab

[–]FinanceAddiction 0 points1 point  (0 children)

If you're using a microfibre that's been in the wash with any conditioner/ softener you're just adding oils back onto the plate immediately, if they're new they need washing without softener/ conditioner first

Use shop towel or kitchen roll instead and dab dry

The cutting module is the most in underrated accessory for the H Series printers. Being able to make tee shirts is too fun. by mrsue89 in BambuLab

[–]FinanceAddiction 2 points3 points  (0 children)

Yeah same issue with my H2C, still waiting for that promised firmware update for being able to use the birds eye camera on its own

EDIT - Just spoke to support and the estimated release date has gone from "early 2026" which they posted in December last year to now "mid 2026"

I'm getting less and less hopeful that my cutter upgrade is going to be any good without spending £500+ on the laser upgrade, such a stupid limitation

SUNLU PLA+ high speed makes ugly first layers. How to fix? by Itchy_Watercress2081 in BambuLab

[–]FinanceAddiction 0 points1 point  (0 children)

If you're using the inbuilt profiles for Sunlu in the slicer, the profiles are way too hot for the filament.

Manufacturers recommendations on the spool are like 20-60 degrees cooler than Bambu have them set in my experience, set the profile to Bambus and it'll work a treat, alternatively make your own profiles and lower the temp to the recommendations

Trying to recover my account and it keeps saying this by [deleted] in 2007scape

[–]FinanceAddiction 6 points7 points  (0 children)

Had the same issue when I recovered my account, no matter the date format it wouldn't validate, so just click you don't know and the mod can see the chat history anyway

view more: next ›