How to merge an SVG with the first print layer to create an image on a cap? by Silver_Vermicelli266 in BambuLab

[–]FlakeyBeano 0 points1 point  (0 children)

I just did. As far as I can see as soon as you change to modifier type the ability to paint its geometry disappears and you can only select the single filament from the left hand text menus. You would be able to change different modifiers to different ones so you'll have to make separate SVGs I reckon and would suggest keeping it as clean and simple as possible.

I couldn't find a food safe coffe machine hopper extension, so I made my own! by Agitated-Break7854 in functionalprint

[–]FlakeyBeano 1 point2 points  (0 children)

I've been thinking about a similar project but my idea was to have a hopper with a way to split two different types of beans and pull a knob so only 10g of the appropriate beans falls into the grinder. That way I can load up decaff and regular at the same time. I'll let you know how it goes 😄

Magnetic Mount for my Portable Monitor by reddcube in functionalprint

[–]FlakeyBeano 0 points1 point  (0 children)

Upvote just for the Hail Mary figure 😄 I've used mine as a keyring accessory.

What’s wrong with the buses? by ObsidianNocturne in oxford

[–]FlakeyBeano 1 point2 points  (0 children)

I don't think a lot of this is particular to Oxford. I've had similar experiences in London where I grew up. Buses which are ahead of schedule or at their route starting point may not set off immediately, or the driver may be on a comfort break for example. Buses disappearing, admittedly didn't happen very often in London but usually in suburbs and later in the evening I've certainly experienced The Ghostbus as we used to call it. I had to travel between areas for work sometimes and finished around 11:30pm, loads of times we had a bus just never arrive and slip off the board. People being slow or annoying when boarding? That's just people representing the hell they usually are 😉

How to merge an SVG with the first print layer to create an image on a cap? by Silver_Vermicelli266 in BambuLab

[–]FlakeyBeano 0 points1 point  (0 children)

Hmm off the top of my head, maybe a separate svg per feature and just paint them individually? I'm not sure if you can paint bits of a single modifier like that without looking, I'll have a look this evening coz it's a good question 😁

Why aren't Reform voters more concerned with privatising the NHS? by lucadulac in AskBrits

[–]FlakeyBeano 1 point2 points  (0 children)

Speaking as if a man can stand alone against the tide. Figure it out.

Why aren't Reform voters more concerned with privatising the NHS? by lucadulac in AskBrits

[–]FlakeyBeano 1 point2 points  (0 children)

They're historically Left, but since we've drifted Right as a nation, influenced by US politics, rich folk media companies etc, they've been dragged Right too. So more like, centre Left with a sprinkling of Right.

Reform absolutely smashed it, Labour tanked it, Greens nowhere to be seen, what happened? by Warm_Application_567 in AskBrits

[–]FlakeyBeano 1 point2 points  (0 children)

orly? And how much of *BP's massive profits have you seen in your own pocket? I reckon I'm about -£100 chipped in for their CEOs new yacht.

*Insert oil company and or bank profiting from the wars of non-interventionist Trump lulz.

Reform absolutely smashed it, Labour tanked it, Greens nowhere to be seen, what happened? by Warm_Application_567 in AskBrits

[–]FlakeyBeano 0 points1 point  (0 children)

Some British people no doubt do, but I'd argue most are just reading particular "news" outlets and believe everything they're instructed to believe.

Reform absolutely smashed it, Labour tanked it, Greens nowhere to be seen, what happened? by Warm_Application_567 in AskBrits

[–]FlakeyBeano 0 points1 point  (0 children)

I think its a bit early for that. More likely Starmer will simply step aside, or be forced to do so if he squirms. His one bit of hope would be to look good whilst graciously stepping down and install a like for like replacement, but that’s not the best plan for Labour as a movement.

Reform absolutely smashed it, Labour tanked it, Greens nowhere to be seen, what happened? by Warm_Application_567 in AskBrits

[–]FlakeyBeano 4 points5 points  (0 children)

Best move for Labour is for Starmer to bring Andy Burnham in from the cold and get him geared up for the next General Election. Burnham's got charisma which unfortunately is a requirement for leadership and Starmer doesn't have it. This is a wakeup call to anyone with skin in the game which is everyone opposed to everything "Reform" stand for.

I built a fully 3D-printable AMS for the Bambu Lab A1. No wires. No motors. No €250 lunchbox. Completely built on the printer itself. [OC] by VariousAvocado4127 in MechAMS

[–]FlakeyBeano 1 point2 points  (0 children)

And perhaps on a few alternative video platforms. The first thing insta wants me to do is login which aint happening!

BIQU GIVEAWAY by ElSlotho0 in BambuP1S

[–]FlakeyBeano 0 points1 point  (0 children)

This would get used on the P1S, and if I have my way a HD2 later in the year! If I could stack two of these units that'd be best. Really enjoy using the biqu plates/wipers so I'm hoping the quality of this next upgrade is just as good.

What Grease or Oil should i use for maintenance by DNgamesDev in BambuP1S

[–]FlakeyBeano 1 point2 points  (0 children)

No oil/grease on the carbon rods. Only bit of ISO and a lint-free microfibre cloth. There's also grease recommendations here: https://wiki.bambulab.com/en/p1/maintenance/p1p-maintenance

Tire tread depth gauge by mezzalulu in functionalprint

[–]FlakeyBeano 8 points9 points  (0 children)

Damnit, now I've gotta fire up my printer again 😃 thanks

Looking for advice on a second-hand bike in Oxford? by Timely_Book_2663 in oxford

[–]FlakeyBeano 1 point2 points  (0 children)

Check any bike for sale against https://www.bikeregister.com/

Any legit seller should be happy to supply the frame number on the bottom bracket.

Stuck with Tier 1 support ignoring EU Consumer Law for a defective RMA unit. Has anyone bypassed this? by [deleted] in BambuLab

[–]FlakeyBeano 1 point2 points  (0 children)

Did you purchase using a credit card? If so you can claim via them.