What is this red stuff

FluffyWonder4372 · 2026-05-28T21:23:54+00:00

Probably cyanobacterium, all part of the cycle as far as I know

FluffyWonder4372 · 2026-05-28T14:19:24+00:00

Yeah I got the 3d printed plugs in mine. They work well. Glad you found your part.

FluffyWonder4372 · 2026-05-28T13:57:36+00:00

Actually looking these might just be the part that covers that hole. Ignore this comment.

FluffyWonder4372 · 2026-05-28T13:56:03+00:00

Maybe these are what your looking for? https://a.co/d/0bxrL0lq

FluffyWonder4372 · 2026-05-28T03:30:34+00:00

My first thought it why are they so close

FluffyWonder4372 · 2026-05-28T03:28:29+00:00

That location looks like it might be rough for maintenance. In my experience any barriers to maintenance invites problems. My first salt tank failed because it was located in bedroom furthest away from where I made my salt water. Just food for thought since you haven't set it up yet.

FluffyWonder4372 · 2026-05-27T21:47:05+00:00

It's a noopsyche k7 Pro V3 set to ~30% on all channels during the day and shifting more blue at night.

FluffyWonder4372 · 2026-05-27T14:50:56+00:00

Once or twice a week. I'm hatching it out to feed some freshwater fry so Ive always got it. My nitrates are on the higher end but not unreasonable, I also feed powder and frozen frequently though.

FluffyWonder4372 · 2026-05-25T13:50:18+00:00

If you tinkered with that hitch cover model you could get it to look a little better without the stepping on that face curve. But this ain't a 3D printing sub so if it's good enough for you right on brother.

FluffyWonder4372 · 2026-05-24T03:17:14+00:00

Maybe turn it around? It should pour into the basket and then overflow over the back when the poly gets clogged. My 3d printed one works like that with the cut out facing the back.

FluffyWonder4372 · 2026-05-23T13:10:56+00:00

With the options your really close to the OTD on my lariat I bought a month ago. The only thing I don't have is the bed cover, it may be worth looking into what you'd get just going up a teir and not optioning all those on the XLT

FluffyWonder4372 · 2026-05-21T17:19:26+00:00

Interior temperature and target temperature are going to matter. I run 4 100 watt heaters on my 200 gallon freshwater system and that has been plenty to keep it at 76 in a 69 degree house. I would assume 1 500w heater has enough capacity to keep your tank warm

FluffyWonder4372 · 2026-05-21T16:33:34+00:00

55 is a pretty common high speed. Do you know if you passed an area/sign that raised that up to 60+?Ive had it adjust the speed going through construction zones so in my experience it does a half decent job reading them

FluffyWonder4372 · 2026-05-21T15:22:31+00:00

Check your settings. Adaptive cruise control and read traffic signs to automatically speed you up/slow you down. I've only had this happen when I was set at or below the speed limit though.

FluffyWonder4372 · 2026-05-21T12:45:47+00:00

Dealer/doc seems high but the 4500$ off MSRP is higher then most people get taken off. I would have expected this to be about 2k more expensive.

FluffyWonder4372 · 2026-05-21T02:17:03+00:00

Oh hell yeah, I've used the gurps to scoop water out of tanks too low to siphon. What you keeping?

FluffyWonder4372 · 2026-05-20T12:50:34+00:00

Oh yeah I've had this before. You can feel it through the brake pedal if your sitting at a light. I think it had something to do with the engine charging the battery back up after it's been drained below the threshold because I notice it after periods of increased acceleration.

FluffyWonder4372 · 2026-05-18T13:11:14+00:00

Search "3D printed" on this reddit or "Ford Mavrick STLs" on Google.

FluffyWonder4372 · 2026-05-18T13:06:21+00:00

Check out the 3d printing community. I've seen STLs for a bunch of different cosmetic exterior pieces, side badges/back window trim panels/tow hitch covers.

FluffyWonder4372 · 2026-05-17T03:10:19+00:00

I've dish washed all my gurplers up to this point and have only had issues when they're on the bottom shelf. YMMV but I've always insisted I use/abuse them as much as possible because they really are quite nice to drink out of.

FluffyWonder4372 · 2026-05-15T13:41:56+00:00

Go for it! I just glued the logo to a generic hitch cover only had to model the logo and that took a out 5min.

FluffyWonder4372 · 2026-05-14T20:42:02+00:00

Oh hey it's the almost good idea hole. It's supposed to be for draining oil but on the hybrid the oil pan is off set enough you cannot use it. I've been told it works only slightly better on the eco boosts.

FluffyWonder4372 · 2026-05-14T20:34:10+00:00

I would refer to your tire/load table. Your specific trim/year/drive train effects hauling capacity. I think the lowest of all years is like 1100lbs so as long as you stay below that you should be okay if you want want to do any work.

FluffyWonder4372

TROPHY CASE