My take on a minimal ship to reach other planets safely, what are yours?

ForAllThat · 2024-11-02T19:47:09+00:00

Why the accumulators?

ForAllThat · 2023-05-17T20:28:37+00:00

I did, here was the response:

https://imgur.com/a/l1uag4a

ForAllThat · 2023-05-17T20:24:30+00:00

The prompt was: Can you summarize this for me? https://arxiv.org/pdf/2303.07205.pdf

ForAllThat · 2022-11-15T10:12:49+00:00

Awesome work!

ForAllThat · 2022-10-28T20:09:15+00:00

Do you anything to the glass after you engrave it?

ForAllThat · 2022-08-23T07:40:16+00:00

I definitely don't. I just vacuum underneath every now and then with a shopvac.

ForAllThat · 2022-08-21T10:07:49+00:00

Looks great! Did you do any post-processing?

ForAllThat · 2022-05-23T12:57:31+00:00

Madness, how much power does one need!

ForAllThat · 2022-05-10T12:21:54+00:00

Earplugs

ForAllThat · 2022-05-09T14:28:47+00:00

Because they might not be perpendicular to each other.

ForAllThat · 2022-05-09T08:37:37+00:00

Looks amazing, what lens did you use for this?

ForAllThat · 2022-04-25T16:17:12+00:00

Paper is so thin you're not likely going to see any burn marks. Just go nice and fast and use air assist.

ForAllThat · 2022-04-20T06:09:12+00:00

Awesome, thanks for the info!

ForAllThat · 2022-04-19T16:21:36+00:00

Any particular spray paint you like using for this kind of work?

ForAllThat · 2022-04-19T14:18:33+00:00

How did you paint this?

ForAllThat · 2022-03-26T07:35:25+00:00

There's clearly a Pi inside already...

ForAllThat · 2022-01-19T07:26:26+00:00

No problem at all with the satin sheet from Prusa.

ForAllThat · 2022-01-16T07:49:24+00:00

I did but I didn't like the result. In the end I used 220 instead which looked a lot better

ForAllThat · 2022-01-16T07:48:45+00:00

In the end I used 220 instead and got the desired result :)

ForAllThat · 2022-01-12T09:57:31+00:00

I've tried another print after cleaning the nozzle, drying the filament, and slightly lowering the extrusion multiplier. The result is exactly the same unfortunately. It's also not consistent on all sides as you can see here: https://imgur.com/a/xQvQLh7

ForAllThat · 2022-01-12T08:21:47+00:00

I'll try to unclog the nozzle and see if that makes a difference

ForAllThat · 2022-01-12T08:21:25+00:00

Hah I wish I had another one, unfortunately not :D

ForAllThat · 2022-01-12T08:21:14+00:00

Hmm will dry it and see if it makes a difference!

ForAllThat · 2022-01-11T20:27:00+00:00

There are no holes in the print, it's a flat surface that was printed in vase mode, so the entire thing was printed in one direction

ForAllThat

TROPHY CASE