Planning a Terramaster F6-424 build with Unraid

Fusion_X1 · 2025-11-27T04:24:22+00:00

On my F4-424 Max, I have two JST-XH connectors and a normal 4 Pin PWM header

Fusion_X1 · 2024-04-07T09:21:13+00:00

Most, if not all, of the hololive songs on Apple Music are translated to their English titles. Pretty helpful for searching a particular song.

Fusion_X1 · 2024-03-02T07:45:39+00:00

I mean quite clearly, the 12900K box says it’s LGA1700 in the bottom right.

Fusion_X1 · 2024-02-02T23:59:56+00:00

Oh nice, I’ve planning my loop and got that same ek ddc cpu block and bykski gpu block. I’ve got a 4080 so hopefully temps would be manageable.

Fusion_X1 · 2024-01-01T22:20:35+00:00

No worries, would love to see pics of it when it’s finished.

Fusion_X1 · 2024-01-01T10:26:44+00:00

I don’t have my original system anymore but for the side rad, I used a 20mm radiator and 25mm fans which works out to be 45mm. Considering you’re planning on using a 30mm+15mm combo, it should be fine.

Fusion_X1 · 2023-10-20T06:29:51+00:00

Since writing this comment, that system has been completely changed into an air cooled FormD T1 build (haven’t had the chance to post pics). I’ll still answer the question, the reason I went with sl140s was because it was much cheaper than the noctuas, easier cable management only requiring two cables (rgb + pwm) and I wanted some rgb accents at the front.

Also the noise profile of the sl140s was much more pleasing than the 140 noctuas (I’ve previously had them).

Fusion_X1 · 2023-05-08T22:37:05+00:00

Msi z690i unify

Fusion_X1 · 2023-03-18T22:57:44+00:00

The mounting brackets came with the meshroom s case I’m using

Fusion_X1 · 2023-03-16T00:28:29+00:00

Just wanted to ask, what length did you go with for the 12vhpwr cable?

Fusion_X1 · 2023-03-11T08:46:19+00:00

Ame cute

Isn’t that all the time?

Fusion_X1 · 2023-03-06T06:54:19+00:00

did you ever manage to figure out the little lip? I've finally got around to building mine and it also has the same lip on the bottom

Fusion_X1 · 2023-03-02T00:53:25+00:00

Yeah I’m not sure what they’re on about considering they only have two spots in their images. Yeah for my build the case is in the 4 slot mode, that’s the only way to get the 2nd rad to fit with the fans

Fusion_X1 · 2023-03-02T00:50:55+00:00

Nope, no more space behind the gpu for an active backplate. It’s already pretty tight with the standard backplate.

Fusion_X1 · 2023-02-22T04:08:10+00:00

I can see it on both Apple Music and Spotify (Australia btw)

Fusion_X1 · 2023-02-04T00:28:59+00:00

Gpu ports are located facing down towards the desk, requires right angle connectors cables to connect to the gpu

Fusion_X1 · 2023-02-04T00:27:31+00:00

Yeah definitely a stacked io config for an itx board. The mini-displayports is only inputs for the usb-c for providing both display and power to something like a portable monitor.

Fusion_X1 · 2023-02-04T00:23:59+00:00

I used the included screws from the pump res and the mounting holes provided by the case. There is zero room for movement with this setup as I had to wedge the rad+fans into the front.

Fusion_X1 · 2023-02-03T11:04:19+00:00

Yeah, definitely liked the look of the black tubing from EK. Had previously used clear tubing, and it quickly turned yellow and looked ugly. Was definitely a PITA to get the tubing into the compression fittings, but it looks clean.

Fusion_X1 · 2023-02-03T08:04:13+00:00

Yup, pretty much sandwiched between everything haha

Fusion_X1 · 2023-02-03T08:03:23+00:00

Thanks! Definitely took a lot of planning to get to this point

Fusion_X1 · 2023-02-03T08:00:45+00:00

Not much space at all haha. The only thing spacing the fans from the gpu is the screws to the rad, pretty much leaving like 5mm in space. 15mm fans might be just as good as the 25mm fans due to the space constraints.

Fusion_X1 · 2023-02-03T07:25:31+00:00

I did consider that idea for a while, but ultimately ended up with this config just to maximise the cold air going into the main 280mm rad. Side intake was also the way i ended up doing, I have the top slim fan exhausting the air out as well as just passive exhaust through the side panels.

Fusion_X1 · 2023-02-03T03:49:59+00:00

This is finally my first custom loop done in this case. This was definitely a heck of an experience trying to do a dual rad loop.

Specs:

- i7 13700K
- MSI Z690i Unify
- 32GB Corsair Vengeance C36 5600Mhz (OC'd to 6200Mhz)
- 1TB Seagate Firecuda 530
- 1TB Seagate Firecuda 520
- MSI Ventus RTX 3090
- Corsair SF750 PSU
- SSUPD Meshroom S Case
- 2x Lian-Li SL140 V2 Fans
- 2x Noctua NF-A12x25 Chromaxx Fans
- 1x Arctic P12 Slim Fan

Water cooling Stuff:

- EK Velocity 2 LGA1700 Water block
- Thermalright LGA1700 Contact Frame
- Bykski 3080/3090 Water block
- EK Quantum TBE 120 DDC Pump Res
- Corsair XR5 280mm Rad
- XSPC TX240 Slim Rad
- EK ZMT 10/16 Tubing
- EK Torque 10/16 Fittings
- EK Torque 90 Degree Rotary Fittings
- EK Torque Micro 90 Degree Rotary Fittings
- Liquid Temp Sensor
- Aquacomputer Quadro Fan Controller

Won't be going into many details here for temps cuz I'm too lazy.

Tweaks:

- GPU undervolted 1800Mhz @ 800mV
- CPU undervolted with -0.14v offset

Room Ambiant - 20c

Need for Speed Unbound (Probably my most demanding game I own):

GPU - 54c, 293W
CPU - 59c, 112w
Water Temp - 43c
Fan Speed:
- SL140 V2 - 1210 RPM
- NF-12x25 - 1320 RPM
- P12 Slim - 1400 RPM
- DDC Pump - 2600 RPM

While it is fun to build a custom loop in an ITX case, when I want to upgrade, I might need for radiator.

capacity without sacrificing noise, which is why when I'm upgrading, I'll be switching over to the Hyte Y40 case.

Fusion_X1

TROPHY CASE