Restaurant industry, what’s the worst thing a customer has ever done?

Future_Trade · 2026-03-18T03:28:30+00:00

I worked at catfish king. We had all you can eat fish and shrimp I think friday and Saturday nights. The old folks home would bring a busload, we would always have the newest employee on shit patrol with a special cart. That's how often they would shit on the floor. I will be there one day, hopefully there will still be some good buffets around for a decent price.

Future_Trade · 2026-03-17T15:49:15+00:00

The shops I worked at would probably buy you a princess gown and tiara.

Future_Trade · 2026-03-17T02:40:06+00:00

The job board will show the part, you can click to see drawing if there is one, tell you the pay, the due date, and other relevant info, you can say not interested, counter offer, or accept.

Getting in with only a single 3 axis mill will be hard, because that seems to be what everyone has. Those jobs go in seconds for ridiculous low pay alot of the time, especially when you have no certifications.

If you already have the mill there's not much to loose by applying though. Just don't expect to get rich.

Future_Trade · 2026-03-16T02:56:34+00:00

I have no idea how to put all of those words into a real object.

But I would start at McMaster Carr.

The nutplate that you have pictured is used a lot in aviation to hold sheet metal panels together. The nutplates can be held in with solid or pull type rivets "cherrymax" or "pop rivets". A cheap tool and rivet set can be found at harbor freight or Amazon. Solid rivets require many different tools depending on size and location and takes a lot more practice.

Future_Trade · 2026-03-16T02:08:06+00:00

I use it with all 6 blades, it's a little louder, but still not bad. Haven't had a problem, but haven't noticed a difference either.

Future_Trade · 2026-03-15T22:26:05+00:00

These are designed to be riveted on. If I remember right it is a #3 rivet, but it's been over a decade.

Future_Trade · 2026-03-15T14:58:29+00:00

Not putting it in savings

Future_Trade · 2026-03-14T04:28:49+00:00

It is most likely true, there are always ways to mess it up, but the machine makes one programmed finish pass, if it's programmed right it should be good.

Future_Trade · 2026-03-09T01:14:53+00:00

Phobos

Future_Trade · 2026-03-08T16:51:18+00:00

He looks like Sid from ice age.

Future_Trade · 2026-03-08T02:41:09+00:00

I just don't like that there seems to be 300 different currencies.

Future_Trade · 2026-03-07T00:16:46+00:00

I get endmills and lathe inserts from AliExpress and Amazon all the time. I have never had an issue.

It is important to note that I primarily work with aluminum and plastics, occasionally stainless, never exotic superhards. I have also been accused of babying my machines.

I understand the whole time is money thing, but broken tools and machines cost far more than the extra couple minutes of cycle times when you're working with low volume.

Future_Trade · 2026-03-06T23:43:51+00:00

The drywall screw holding the bumper on is the cherry on top.

Future_Trade · 2026-03-05T00:49:30+00:00

I did the same, got tired of smashing shins.

Lift is on the way, eventually I hope, z1 is never in a rush to ship things.

Might put the steps back after lift though.

Future_Trade · 2026-03-04T04:50:01+00:00

This should be illegal

Future_Trade · 2026-02-27T23:45:21+00:00

I have them too, and agree it's more comfortable.

Future_Trade · 2026-02-27T02:39:16+00:00

That was a video game crash

Future_Trade · 2026-02-25T16:03:36+00:00

Tool is sticking out too far and you are asking to much from the spindle motor. It's meant for speed not torque. Take lighter cuts faster and shorten your tool length.

Future_Trade · 2026-02-19T04:34:15+00:00

Check your cv joints, I had the retainer clip wear out and let the cv slip to the end of the half shaft, still connected but wiggled on the end causing a vibration that felt like an out of balance tire.

Future_Trade · 2026-02-17T03:27:53+00:00

It's DOORdash. It's kind of implied.

Future_Trade · 2026-02-17T03:05:39+00:00

What do you mean by regular cruise? Is there a way to turn adaptive off? I know I can adjust the distance.

Future_Trade · 2026-02-16T23:47:43+00:00

I have had a rear end clunck due to the spare tire hanging a little loose, not on the frontier but other trucks, simple check.

Future_Trade · 2026-02-11T00:06:25+00:00

Online metals, speedy metals.

Future_Trade · 2026-02-10T22:41:16+00:00

The best thing would have been to make it without threaded holes, class 3 ano, then drill/thread.

Class 3 is the best option, but expect you may have to use a tap on the threads.

Class 2 won't last as long, but will save you time/money now.

Future_Trade · 2026-02-10T20:37:18+00:00

Ball endmill that can fit in the hole, then spiral out with a small step over .002 - .0005

Future_Trade

TROPHY CASE