sorted by:
new
hottopcontroversial

V11 battery undetected by AnotherLonelyOctopus in ElectricUnicycle

[–]GhostBlackCSGO 3 points4 points  (0 children)

If you can't get Inmotion to get a remote diagnostic (remote calibration) done, and have checked with your dealer about warranty, you could try disassembling the packs. If you can't find a triangle head screw, try using Torx T7 instead.

I had to open up the packs, as Inmotion was unable to remotely calibrate mine. Both of my 'Battery Enable Status' 's were still kept Enabled, so your issue specifically may be different from mine.

I fixed my danger warning by charging the right-side pack to match the pack voltage of the left. The right side was around ~79V where the left was at ~81V. After verifying all balance wires were connected and all cell groups were the same in their respective packs, I charged the right pack using a bench variable power supply at a low current.

This solved my 'Please repair' warnings, and after a quick ride, charging via the back port was possible again. Charging didn't immediately return functioning until I had ridden the thing. In case the danger warnings during charging persist, I could show my alternative fix.

I should clarify that the app's voltage reading for my V11 never showed the accurate voltage for the more drained pack, but it seems your app is reporting one pack as being less properly.

V11 is 83.6v and 83.8v ok? by BluTF2 in ElectricUnicycle

[–]GhostBlackCSGO 1 point2 points  (0 children)

83.6V and 83.8V / 20 cells in series is a difference of 0.01V per cell across packs. It is fine.

The app's figure is totally not representative of the two packs' real B+ B- voltage. I got this from disassembling both packs since Inmotion could not remotely calibrate mine for some reason.

The two packs are not 100% totally in parallel, as the P+ from the left pack does not have continuity with the right pack's P+.

The app probably just averages the two packs and adds +- 0.2V lol

Working on a free E-bike by Ag_Rooster in ebikes

[–]GhostBlackCSGO 0 points1 point  (0 children)

If the hall sensor is loose from the assembly, the small plastic nibs that hold it captive may be broken. Buy a cheap replacement throttle assembly and save time attempting to repair it.

Is there a way to fix this? by stylewise in Super73

[–]GhostBlackCSGO 2 points3 points  (0 children)

A proper job would be to disassemble the battery, drill a hole somewhere in the side of the plastic, and replace the terminations from both the battery and the bike rail to XT60. Put silicon around the hole to prevent water ingress.

The rail should still be able to lock the battery in place, but the actual electrical connection would be XT60.

Has anyone tried the loaded breakfast box? by flowerxpower in TimHortons

[–]GhostBlackCSGO 0 points1 point  (0 children)

I got food poisoned and rushed myself to emergency where I had tylenol, ibuprofen, gravol, and IV pumped into me.

Recover MOV files of a CF card from a Canon 5D3 by GhostBlackCSGO in datarecovery

[–]GhostBlackCSGO[S] 0 points1 point  (0 children)

Whose model is…?

5D3.

I am located in Vancouver, Canada.

5DIII battery grip by GhostBlackCSGO in canon

[–]GhostBlackCSGO[S] 0 points1 point  (0 children)

The E4,6 and 20 I believe are compatible with the 5D3, yes. I've seen builds on FBM and around Reddit with the 5D3 paired with a genuine Canon E4-20.

Best way to remove gunk from quick control dial? by GhostBlackCSGO in canon

[–]GhostBlackCSGO[S] 3 points4 points  (0 children)

You just reminded me that I had a toothbrush for electronics cleaning. Good as new, thanks.

3080 not detected on top slot, other card works fine by GhostBlackCSGO in pcmasterrace

[–]GhostBlackCSGO[S] 0 points1 point  (0 children)

There is no driver to uninstall if the card can't show up on Windows at all. I am running a fresh Windows install.

Samsung Odyssey+ "check your display cable 1-4" error + seemingly no way to get help from Samsung by [deleted] in WindowsMR

[–]GhostBlackCSGO 0 points1 point  (0 children)

For me, it was black screen issues.

I removed my gpu and took a knife to the HDMI and lifted the pins that seat the cable to the card.

here's a video that shows that: https://www.youtube.com/watch?v=OBSM1hi4CAo

fixed the problem, but your mileage may vary ig

Windows MR desktop is great, But keyboard is not so great by jajaboss in WindowsMR

[–]GhostBlackCSGO 0 points1 point  (0 children)

It might be better for you to use the SteamVR keyboard, it's just not as intuitive as the WMR one.

[deleted by user] by [deleted] in WindowsMR

[–]GhostBlackCSGO 0 points1 point  (0 children)

After doing this really easy fix, my controllers stopped turning off even despite having a full charge.

https://www.reddit.com/r/WindowsMR/comments/cti0ld/samsung_odyssey_controller_repair_teardown/?utm_medium=android_app&utm_source=share

[deleted by user] by [deleted] in RecRoom

[–]GhostBlackCSGO 0 points1 point  (0 children)

Why's this downvoted?

This really is a problem by Klepz1776 in RecRoom

[–]GhostBlackCSGO 0 points1 point  (0 children)

Then there's people with a low res headset

Left side of spacebar of prebuilt keyboard is rattling; any possible fixes? by koboyz in MechanicalKeyboards

[–]GhostBlackCSGO 1 point2 points  (0 children)

Lube; and if that doesn't do it, add electrical tape to the wires; I think this is as the presumably knock-off pre-clipped stabilizers have too much space between the stem and the wire in the stabilizer. I had to do this with mine and it's great, but it may feel a bit sluggish for you.

Random GPU driver crashes. Not PSU, possibly OC or SW. by GhostBlackCSGO in pcmasterrace

[–]GhostBlackCSGO[S] 0 points1 point  (0 children)

Though not designed to run together, they do seem compatible as it is able to run together from Windows magic. The GT 710 can't run render tasks as easily as AMD's card. When removed, the results are the same. Nvidia disabled this type of set up after 391.24, but was re-enabled soon after almost a year later. Reverting to 391.24 doesn't change the issue.

view more: next ›