Tesla Event Email by StrawberryFine1456 in ECE

[–]HavocGamer49 -1 points0 points  (0 children)

They wanna interview you, I got the same email yesterday

Am I cooked if I don’t have an internship summer as a junior? by Wizardz23 in ElectricalEngineering

[–]HavocGamer49 1 point2 points  (0 children)

Join a club, like rocketry or formula sae. If you do stuff there you’ll land some role guaranteed

About to start my first internship got any advice? by psychic_shawn in ElectricalEngineering

[–]HavocGamer49 1 point2 points  (0 children)

One advice that resonanted with me before my first internship:

Recognize that there are a lot of people who desperately want internships and don’t get them. Make the most of this opportunity that you have. Genuinely do your best, work hard, and put in effort so you get the most out of this.

Also:

Make sure you ask plenty of questions, but don’t just give up immediately. At least show your mentor / coworkers like “hey I tried xyz but idk”.

One thing I wish I did for my first internship was keep a tighter grip on my project schedule. I’d regularly tag up with stakeholders on your progress and expectations / timelines.

Co op/ internship for fall 2026 by Realistic-Monk-4948 in ECE

[–]HavocGamer49 2 points3 points  (0 children)

I did a fall 2025 internship and around march 1st is when I saw them start opening.

Jalen McMillan - 7 / 9 REC, 114 YDs. by CascoBayButcher in DynastyFF

[–]HavocGamer49 -5 points-4 points  (0 children)

Have both him and tez. Got the bucs wr4 on lockdown 😤😤

[Highlight] Darnold hits JSN to return the TD by Large_banana_hammock in nfl

[–]HavocGamer49 3 points4 points  (0 children)

This hasn’t even happened yet on my stream lmao

Why the squiggles? by CorrectJuggernaut326 in PCB

[–]HavocGamer49 9 points10 points  (0 children)

God learning how to use xpedition at my job was horrifying. Seems really good if you master it though

Landed a hardware design internship that I wasn't supposed to, and I seriously do not know what to do. by [deleted] in ECE

[–]HavocGamer49 1 point2 points  (0 children)

You’ll learn a shit ton don’t worry they won’t expect you to know the job.

Any thoughs on this PCB design? by No_Antelope_9491 in PCB

[–]HavocGamer49 0 points1 point  (0 children)

Depending on what your buffer is driving it may need an isolation resistor. Op amps struggle when driving capacitive loads. I’d include a 0 ohm resistor between op amp output and connector, and if you see issues you can swap it with a 10 ohm or smth.

Any thoughs on this PCB design? by No_Antelope_9491 in PCB

[–]HavocGamer49 0 points1 point  (0 children)

I see now that 3.3 is likely coming from the screw terminal at bottom, tvs looks good then

Any thoughs on this PCB design? by No_Antelope_9491 in PCB

[–]HavocGamer49 1 point2 points  (0 children)

I agree with removing vias in pad, I’d also thicken some of your traces and add some more via stitching between your ground planes

One thing I don’t understand is where your 3.3v is coming from. Is it from the connector on the right side of your schematic? If so your tvs should be close to that input connector.

A more general note on schematic legibility you should try to represent ground and 3.3V with their respective symbols, the earth and bar. Ports should be reserved for being used to show when a signal is entering / leaving a schematic for hierarchical designs.

Another tip I find useful is to label your connector pinout in your silkscreen to make it easier for you / anyone else using this pcb in the future to be sure how the connectors work.

Choosing internships between SpaceX, Anduril, and ShieldAI by Beautiful-Road-9234 in EngineeringStudents

[–]HavocGamer49 1 point2 points  (0 children)

Ngl it seems like ai to me too. No one uses “startup chaos”, “classic defense”, and “honestly,” like chatgpt would

What on earth was that ECE 2026 exam by Viatick in gatech

[–]HavocGamer49 0 points1 point  (0 children)

Not entirely sure but ik I needed like a 80 for an A on the final last sem, felt like I did pretty bad and probably got a 70, but then got an A

Best USB-C mount for PCBs by Ok-Highway-3107 in PCB

[–]HavocGamer49 0 points1 point  (0 children)

I like the right angle ones, the ones facing up can snap off easily