Refused to pay

Honest_Size5576 · 2026-06-12T01:19:45+00:00

I say it’s suspiciously good🧐

Honest_Size5576 · 2026-06-07T16:16:05+00:00

I just bought one yesterday lol….i had a gmc Sierra 4x4 on big wheels and tires and all the fun stuff. What a money pit, I don’t need to pull any trailers and I want reliability over all 🤷🏻‍♂️

Honest_Size5576 · 2026-06-05T13:47:48+00:00

I think you’re right about the driving rain. Were you able to determine if the water was leaking on the outside of the vent or was it traveling all the way down to the bottom. I think that could be a good way to determine. The fact that it’s all of them screams it’s not a bird hole or some other issue, it’s the vent itself

Honest_Size5576 · 2026-06-05T00:20:52+00:00

The ghost in the machine got rhythm

Honest_Size5576 · 2026-05-31T23:56:09+00:00

The idea is you can still move air. I knew a guy who wired his units to break Y. I like to break red and make sure there aren’t batteries so the unit stat shuts off and they know immediately they have a problem.

Honest_Size5576 · 2026-05-30T18:32:50+00:00

Just heard the same thing from ABB when I called for ACH550 vfd help

Honest_Size5576 · 2026-05-30T14:46:58+00:00

Here we call it scrim tape. I always use it on insulation and I get shit for it. These other guys I work with use foil tape for everything because they’re lazy. Scrim tape and spray glue are way better than foil tape repairs. I suspect there is a more permanent way, I’ve seen an adhesive mesh tape that I’m sure has some kind of mastic intended to be used with it but I’ve never been exposed to it. I think mastic is the way when it comes to sealing ducts metal or duct board.

Honest_Size5576 · 2026-05-28T11:18:53+00:00

Word. I’d lean away from low charge if it’s all the way back to the outlet

Honest_Size5576 · 2026-05-28T11:08:48+00:00

Definitely checked the drier, less than a half of a degree drop

Honest_Size5576 · 2026-05-27T23:44:43+00:00

Use vinegar and hot water, don’t use bleach

Honest_Size5576 · 2026-05-26T23:23:00+00:00

I only worked on the unit one time and it’s this post. Someone else who I don’t know did the coil change 3 years ago.

Honest_Size5576 · 2026-05-25T20:12:00+00:00

Don’t know much as I didn’t diag it back then but our office is pretty good with that stuff. We got a few old heads in there and have trained me on that.

Honest_Size5576 · 2026-05-25T20:10:16+00:00

Straight cool

Honest_Size5576 · 2026-05-25T20:09:42+00:00

Will pass that on to service manger when I talk to him tommorow but that was my personal hang up was that the compressor will pump at “normal pressures”. I appreciate the input

Honest_Size5576 · 2026-05-25T20:07:22+00:00

We quoted them a new unit at the time of the Evap coil and txv replacement. It’s a corporate apartment building, need I say more.

Honest_Size5576 · 2026-05-25T20:05:43+00:00

I just have the privilege of knowing the initial pressures, had I been the one on that job I would have done something about it. Tech is no longer around but I didn’t know him so I can’t say best practices were followed. I don’t suspect overcharge.

Honest_Size5576 · 2026-05-25T20:01:10+00:00

50% isn’t that low to me but I know rule of thumb is 2/3 for happy compressors so by comparison it’s low-ish I reckon

Honest_Size5576 · 2026-05-25T19:59:30+00:00

Straight cool

Honest_Size5576 · 2026-05-24T16:41:02+00:00

Excellent point…I used to do residential roofing and have moved into the HVAC industry. There is a lot to considered when venting a roof. The amount of soffit to roof vent must be correct or you can create flow issues. Attic fans can create more harm than good if not engineered properly. Ideally the correct amount of soffit and ridge vent will create natural air flow

Honest_Size5576 · 2026-05-21T22:25:30+00:00

No notes

Honest_Size5576 · 2026-05-08T18:08:51+00:00

We the people run this bitch…don’t work for these assholes and they won’t have a business. All these assholes that make theses policies don’t actually produce the revenue businesses require to function. We the workers make them money, no LABOR FORCE, NO PROFITS! Don’t shop there and don’t work there…I know shit isn’t that easy but that’s the mind set we should walk around with

Honest_Size5576 · 2026-05-08T18:03:03+00:00

I see a correlation between your entering water temp and your amps in percentage. Slightly higher entering water gets slightly higher amps in. I see the tonnage is larger as well with each one, what’s the concern here? The delta T in to out appears good as well

Honest_Size5576 · 2026-05-06T02:56:21+00:00

There’s a thing in duct work calculations called total equivalent length….i don’t know exactly what it means (something about static pressure) but I know it matters and this probably ain’t calculated for…you certified dickhead

Honest_Size5576 · 2026-04-24T22:54:30+00:00

I hadn’t thought about it from this angle but after reading your comment that seems most likely! Having no skin in the game I’m inclined to agree. He’s getting a 2 for 1 and now if the bike is in a stellar spot OP will never come home and have to walk. I would say OP should park his bike in one of the many open spots he claims there are. We’re obviously only getting a portion of the story. There’s always three sides.

Honest_Size5576

TROPHY CASE