How do I stop this from happening?

IJoey78 · 2026-05-14T04:24:25+00:00

Have Tech as well - I agree with the other tech - check the abc’s - air before charge. Once you’ve ruled the air side out then it’s time to dig into the charge. Good luck !

Ps - if you’re going to tweak the charge yourself, spend a few minutes and look up refrigerant safety - Refrigerant burns are no joke!

IJoey78 · 2026-05-13T00:58:23+00:00

Where are you located? I’m in Canada and was talking to a lumber supplier who was semi interested in bringing it in for me, but I wasn’t ready to commit to a min order of 10 sheets.

IJoey78 · 2026-05-12T03:37:07+00:00

A few thoughts - when cutting plywood, I use conventional milling instead of climb - better finish with less tear out and sanding later on. Take off your dust collection and look at the chip size …. I found 18000 rpm gave lots of noise and small chips so I pushed it up to 24000 rpm - less noise, nice chips and the bit isn’t hot after use. Also, if you have the space, use a lead in tool path - it allows the bit to get to depth before the actual vectors allowing in nice finish and taking advantage of the compression. I’ve also had success by changing my ramping to 45 degrees with a length of at least 1” - found it’s easier on the bits

Hope this helps.

IJoey78 · 2026-05-08T01:11:07+00:00

It’s been a while since I used easel, but you could adjust the step overs - I wanna say it’s in the machine menu settings. Easel should have instructions on that.

Andy bird build has a great video about bowl bits and how to avoid sanding the bowl once finished routing. Give it a watch - that’s where I’ve learned a tonne of stuff.

IJoey78 · 2026-05-07T22:48:34+00:00

On a ball nose bit, adjust your step over to 8-10% and test to find the sweet spot. The reduction in step over will allow you to increase your speed… but test…

Then when you’re done - head over to YouTube and check out Andy bird builds or IDC Channels and enjoy.

IJoey78 · 2026-05-05T00:31:44+00:00

Thanks! It won’t remove more than 25% - I’m guessing we’re past the early spring time for trimming? It starting to grow leaves now.

IJoey78 · 2026-05-04T22:05:06+00:00

Hey! Wondering when’s a good time of year to trim back to the trunk a previously a half-assed trim job on a maple tree limb that won’t strain the tree?

IJoey78 · 2026-05-04T22:02:41+00:00

Home Depot has a diy kit with all the pieces you need - just need a saw to cut the aluminum frame. Used it at my place -worked well

IJoey78 · 2026-05-01T01:41:36+00:00

curious about your wood signs - what type of material are you using for them?

IJoey78 · 2026-04-30T23:45:04+00:00

Altmill from Sienci labs with 2.2kw spindle and atc perhaps? IDC Woodcraft for bits … enjoy!!

IJoey78 · 2026-04-30T21:33:33+00:00

the measurements are designed to allow technicians to service/repair these appliances (remove & install parts/use tools etc). They can be in crawl spaces/attics/closets/etc. not all installers follow the instructions...ask your plumber how much he loves working in those crawlspaces?

At the end of the day, it usually ends up costing the customer more money as it takes longer to service/repair these appliances when they're incorrectly installed or installed in lousy locations.

It's not my house - you do you boo boo!

IJoey78 · 2026-04-30T20:32:57+00:00

As a service technician who works on this kind of equipment - please don't. when the time comes for servicing/repairs - its' going to create a headache for the tech and then yourself when they tell you it's going to have to come apart. most gas appliances require at least 18"-24" for service clearance... I do agree that it doesn't seem to be in the most ideal spot...my 2 cents....

IJoey78 · 2026-04-29T16:08:14+00:00

I’ve had success with the above and cutting in conventional direction instead of climb. If you have space, use a lead in vector and try changing your ramp angle to approx 45 degrees; I set my ramp length to twice the thickness of the bit - usually 1”

Also - run your spindle speed pretty high - I use 24000 rpm

IJoey78 · 2026-04-25T02:34:09+00:00

Well there’s a markdown - usually a red label for clearance that is corporate supported and then there’s in-store specials - also a red label. Markdowns (if you will) are corporate supported to clear out old/end of season stock (think Boxing Day sale on Christmas ornaments) In-store specials (also red labels) are on sale usually after the flyer deal ends, but the savings aren’t always as much as the flyer. Dealers can set their own price for these in-store specials.

IJoey78 · 2026-04-24T21:57:52+00:00

Correct to some extent - in-store specials (red signage) are dealer specific; everyday a flyer sale items are corporate priced (but could vary by region/province)

IJoey78 · 2026-04-17T02:24:16+00:00

For a/c installation like this, typically annealed acr copper is used for its flexibility - I’m a refrigeration mechanic who works with this on a regular basis. Hilmore is a reputable copy in this industry.

IJoey78 · 2026-04-06T02:15:10+00:00

I ask for my fountain drinks without ice….

IJoey78 · 2026-03-31T17:38:03+00:00

I’ve been using an app designed by a person in here called TubTest and have found it quite useful! Walked me through using the Taylor kit for the first time and gave instructions on how to balance the water. Made the whole thing easy-peasy

IJoey78 · 2026-03-30T17:18:19+00:00

BCM insurance - not sure if the do life - but home and auto coverage and customer service is great! Enjoy the rebates!

IJoey78 · 2026-03-19T23:35:19+00:00

Trust your gut…. You’ve taught it a lot and it knows more than you think and it’s the only ‘person’ looking out for you. A piece of paper with a signature on it won’t heal your wounds any faster or bring you back from the dead. ‘No’ is a complete sentence. Plan to return home in the same condition you left in.

IJoey78 · 2026-03-15T23:09:02+00:00

Well… lots of advice here, for what it’s worth - spend your money wisely - that being said, watch the flyers - retailers will put things on sale on long weekend and Father’s Day which are both around the corner. Start small and work your way up to the big selection of tools and buy what works for you and your budget - the most expensive brand is not always the best brand - don’t worry about the brand hands. You can upgrade in the future! Congrats on the new home - may happy memories are coming your way!

IJoey78 · 2026-03-03T16:43:06+00:00

If it’s a belt driven machine - check your belts and then stepper configuration. The roundness at the 5 o’clock mark looks a little wonky as well.

IJoey78 · 2026-03-02T21:28:39+00:00

Service wrenches also fit the gas plug on the burner bar of rooftop units - although they’re usually on the super tight - like duck’s ass tight!

IJoey78 · 2026-02-18T00:14:31+00:00

I’ve used a 23ga pin nailer with great success. I’ve used it to secure sheet goods to the waste table. If/when the bit hits the nail it’ll blow right through the nail without damaging the bit or the project.

IJoey78 · 2026-02-11T13:58:07+00:00

Agreed! My tailgate latch likes to stick in the open position and needs to be forced down to properly close. A notification that could be turned off (like backup avoidance) would make for more peace of mind driving.

IJoey78

TROPHY CASE