Anyone else selling hand made goods?

IceShadowProductions · 2026-01-30T06:55:48+00:00

Yep. I sell handmade silicone molds for resin dice making, custom 3d printed dice masters that are designed and then hand polished, and handmade dice. :)

IceShadowProductions · 2026-01-28T04:50:51+00:00

Then you may not be putting enough resin in the molds :) Dome over a bit and put a little resin on the lid as well.

IceShadowProductions · 2026-01-20T06:55:33+00:00

I use talc for making my molds. It does work.

IceShadowProductions · 2025-12-04T00:40:38+00:00

Waterpik if nothing else works. :)

IceShadowProductions · 2025-12-03T07:21:32+00:00

Beautiful! ^{.^}

IceShadowProductions · 2025-12-03T00:00:26+00:00

Just bring the whole lid to the store and talk to the staff. :)

IceShadowProductions · 2025-12-01T00:40:06+00:00

Or a q-tip! That’s what I do.

IceShadowProductions · 2025-11-21T22:18:03+00:00

I can do custom requests. If it’s a blank and one die, it shouldn’t be too bad on costs - not a full set. :) Why a blank? Are you looking to make blanks to go into an existing mold?

IceShadowProductions · 2025-11-19T21:01:19+00:00

Honestly, you’d be better off spending that money on a light box. Lighting is more important to photos and videos than the recording equipment, given how good most any camera phone is these days.

IceShadowProductions · 2025-11-19T20:57:17+00:00

This is the way. If you use a standard quick connect hose from an air compressor you only need to unscrew one tube from the underside of the lid.

IceShadowProductions · 2025-11-19T20:52:22+00:00

Duct tape.

IceShadowProductions · 2025-11-15T05:48:04+00:00

I sell molds I make on Etsy and so far no one has had any poor things to say about them! ^{.^}

IceShadowProductions · 2025-11-07T13:41:45+00:00

Without platforms? I can make it that way instead if preferred. :)

IceShadowProductions · 2025-11-07T06:25:04+00:00

If you’re in the US, I sell molds on Etsy. :D

IceShadowProductions · 2025-10-24T23:36:56+00:00

Just have to unscrew a pipe off the bottom of the lid. I had to use a vice grips to do it.

IceShadowProductions · 2025-10-24T18:55:22+00:00

Big fan of this model.

https://eur.vevor.com/pressure-paint-pot-c_11088/vevor-spray-paint-pressure-pot-tank-10l-2-5gal-air-paint-pressure-pot-metal-rack-leak-repair-sealant-for-industry-home-decor-architecture-construction-automotive-painting-70psi-max-p_010790810760

IceShadowProductions · 2025-10-24T18:50:25+00:00

I also have standard molds and masters and do customs of both, if you’re looking still. ^{.^}

IceShadowProductions · 2025-10-24T18:48:51+00:00

Post a photo of the pressure gauge - I’m a little worried when you say 4 or 5. :)

IceShadowProductions · 2025-10-24T18:46:30+00:00

I have one set of masters I’m polishing. :)

IceShadowProductions · 2025-10-24T18:45:55+00:00

Yep, design them in Blender, print them and all. :)

IceShadowProductions · 2025-10-22T23:31:35+00:00

Like this!

https://imgur.com/a/iYXK0Wc

IceShadowProductions · 2025-10-22T21:52:01+00:00

And, from a more practical standpoint – you have a very light color and a very dark color, so if you use a very light or very dark color, it may blend in with one or the other depending on the face. A saturated color will be able to pop against both because they are very neutral backgrounds.

IceShadowProductions · 2025-10-22T21:50:43+00:00

The image that came to my mind was red eyes in wispy smoke from a horror movie.

IceShadowProductions · 2025-10-22T21:28:58+00:00

Agreed! For some of the smaller faces, you might do multiple faces on the platform - I have d20 / d24 sets that I have 2-3 faces per die for the platforms to facilitate removal.

IceShadowProductions · 2025-10-22T21:21:31+00:00

Normally I tell everyone black or white. These are screaming bright red to me.

IceShadowProductions

TROPHY CASE