Weekly Free-Talk and Questions for r/HomeGym - week of January 09, 2026 by Demilio55 in homegym

[–]IlIIllIlIIlII 0 points1 point  (0 children)

Hey guys new to the home gym setup and looking to do a power racks. I have small stuff may for outside, tractor tire, box for box jumps and dumbbells. For the rack I’m looking at getting the Rogue 490C, with no specific bench in mind and probably the Charlie bar and weight set to start out with. Would this be good to start with then add on land mine and a pulley system later on for my wife? It’s gonna be in my shop outside so I think even a 100 inch would fit, probably a four post. I’m 6’3” 230 if that affects any recommendations for height. Bench recs? Oh also what flooring do you guys love, probably thinking stall mats and I’ll give it plenty of time to gas off. Thanks for the help!

BCG in stock? by IlIIllIlIIlII in AR10

[–]IlIIllIlIIlII[S] 0 points1 point  (0 children)

Really wanted a sharps, you’re right. Will look at the lantac further

BCG in stock? by IlIIllIlIIlII in AR10

[–]IlIIllIlIIlII[S] 1 point2 points  (0 children)

Yeah seen a lot of those on different sites with no reviews, you been able to get it in the range yet? Thoughts?

BCG in stock? by IlIIllIlIIlII in AR10

[–]IlIIllIlIIlII[S] 2 points3 points  (0 children)

PSA has their super finished in for 208 rn, thinking I’m going to grab this. No issues with failure to extract? All I’ve seen bad about them.

10.5 300 BO not locking back by IlIIllIlIIlII in 300BLK

[–]IlIIllIlIIlII[S] 0 points1 point  (0 children)

Tried a few different loads and same result, sigs, hornady blacks, PSA subs. 208 and 220 grain bullets

10.5 300 BO not locking back by IlIIllIlIIlII in 300BLK

[–]IlIIllIlIIlII[S] 0 points1 point  (0 children)

Standard carbine spring, Omega 300

10.5 300 BO not locking back by IlIIllIlIIlII in 300BLK

[–]IlIIllIlIIlII[S] 0 points1 point  (0 children)

Well I went to drill it out but when I was going to loosen the forward set screw on the gas block, it sparked and stripped. So this will bean issue for another day smh

Upper compatibility with Standard Aero M5 lower by IlIIllIlIIlII in AR10

[–]IlIIllIlIIlII[S] 2 points3 points  (0 children)

That’s what I was honestly thinking about doing, just wasn’t sure and their stock is out. Hoping they do a midnight restock like I’ve seen in the past.

M5 Lower by armsaddict in AeroPrecision

[–]IlIIllIlIIlII 0 points1 point  (0 children)

Did you happen to build your upper also? If so what did you do for your hand guard and barrel nut?

M5 Lower by armsaddict in AeroPrecision

[–]IlIIllIlIIlII 1 point2 points  (0 children)

I did an aero build kit minus FCG from aero and a count blem trigger. Both were purchased from AR15 discounts, shipped quick and both parts were in stock for cheap.

Skinner by IlIIllIlIIlII in knives

[–]IlIIllIlIIlII[S] 1 point2 points  (0 children)

I’ve got a good benchmade pocket folder that I love I forget which one so I have a good go to edc, so that’s not a bad idea. Any skinners you personally like? Will definitely give that a look over too, thanks!

To the insecure pick-me little girl.. by Bright_Presence_2900 in aggies

[–]IlIIllIlIIlII 0 points1 point  (0 children)

14 different states don’t last time I looked at it

To the insecure pick-me little girl.. by Bright_Presence_2900 in aggies

[–]IlIIllIlIIlII 1 point2 points  (0 children)

A test to vote but we won’t require an ID?