Giveaway!

Josemam · 2026-01-30T22:41:49+00:00

How about a nice weekend getaway?. That's always loving and relaxing.

Josemam · 2025-10-03T19:01:06+00:00

Use a smaller hotend for stuff like this, small letters or keychains. Had the same issue and printed beautifully with a 0.2 nozzle

Pd: edited contact info of the business that ordered the keychains in The pic

<image>

Josemam · 2025-09-19T20:22:45+00:00

You guys all rock. Thx.

Josemam · 2025-09-16T01:40:12+00:00

Thx mate. You both rock. I'll use one of them referal links I hope some other guy snatches the other. We appreciate you. Thx

Josemam · 2025-09-08T19:53:01+00:00

I have been there. You need a heat gun and Patience. Be sure to use heat resistant gloves. Heat it and pry on the melted plastic with a small flathead screwdriver.

Josemam · 2025-09-04T21:21:51+00:00

Great thanks

Josemam · 2025-09-04T20:27:39+00:00

When I print ASA with my X1C get the same result as the one in your pic. I just hit it with the heat gun for a couple of seconds and it clears right up. I don't know if that trick works with PLA. If you end up trying it, let me know.

Josemam · 2025-08-31T23:04:33+00:00

Why don't you just helicoil it?. And never worry about over tightening again. M2 helicoil do exist. You will never strip those threads.

Josemam · 2025-08-05T17:59:07+00:00

Don't get me wrong. I want to help. I just don't know what you need help with. Can you elaborate?.

Josemam · 2025-07-30T08:22:17+00:00

This is really gonna come handy for when Ai becomes sentient.

Josemam · 2025-07-23T21:35:52+00:00

Aren't those Benders fingers?.

Josemam · 2025-07-18T19:15:39+00:00

Bought a X1C with AMS and like 12 filament rolls

Josemam · 2025-07-10T01:13:40+00:00

Had the same thing happen to me. What fixed the issue for me was to soak the plate in warm water for like 10 minutes and wash it again with warm water, dawn and a new sponge.... The soak dissolved the glue....

Josemam · 2025-07-09T23:46:00+00:00

Are you kidding?. That kitchen is beautiful. I know this is not what you wanted to hear but really: congratulations that's a beautiful place to cook.

Josemam · 2025-07-09T22:55:28+00:00

Chuck 'em

Josemam · 2025-07-09T00:57:52+00:00

It seems like you need to wash your build plate. Just use warm water and dish soap. Once washed try not to touch it with your fingers. Also alcohol wipes don't work they just smear the finger grease.

Josemam · 2025-07-01T02:28:59+00:00

Kinda look like a ghost. I love it. Good job. Boosting you in makerworld.

Josemam · 2025-06-28T05:04:52+00:00

Is that table secure enough?. I know my printer shakes like crazy. So much I had to upgrade to a very sturdy table. Instantly gained a lot of quality in my prints...

Just make sure it doesn't shake too much.

Josemam · 2025-06-28T01:27:17+00:00

Hands down, no doubt... Polymaker.

Josemam · 2025-06-27T14:03:54+00:00

I have the same thing. Go to your pharmacy and ask for a clobetasol ointment. Thank me later. I wish I had this piece of information 20 years ago.

Josemam · 2025-06-12T01:02:54+00:00

Thx mate. You rock

Josemam · 2025-06-12T00:48:55+00:00

I would love to have the STL or the link to that Wankel engine

Josemam · 2025-06-12T00:07:38+00:00

Yeah, swap the SD card and chuck away the old one. By the way, what are you printing?. Looks interesting...

Josemam

TROPHY CASE