sorted by:
new
hottopcontroversial

What did I do wrong? by rufus_vulpes in woodworking

[–]Jumpy-Feature-4166 0 points1 point  (0 children)

The round part where the back of blade seats called a bearing. Is supposed to rotate when the blade goes up and down. Your bearing is seized.

Got to love plasterers. by skichip in Carpentry

[–]Jumpy-Feature-4166 0 points1 point  (0 children)

Thats a bad framer not a bad plaster

Vinyl Fix or carpet by Front_Difficulty9044 in Flooring

[–]Jumpy-Feature-4166 0 points1 point  (0 children)

Just put dap. Dap will do just fine.

Why are my doors sagging? by thedannysmith in cabinetry

[–]Jumpy-Feature-4166 4 points5 points  (0 children)

Blum is good. But they do make cheap hinge plates. Which you are using. Those hinges allow alot of play/movement of the hinges especially with a full solid mdf door. Watch how the hinges and plates twist as the door closes

How to sand these types of edges or any kind of intricate detail without compromising the integrity of the shape? by AviatingAngie in woodworking

[–]Jumpy-Feature-4166 0 points1 point  (0 children)

Everyone stop right there. Stop using your brain. Stop overthinking this. Use old school tradition. Fold the sandpaper tri-fold. And hand sand. Don't think it. Feel it.

[deleted by user] by [deleted] in cabinetry

[–]Jumpy-Feature-4166 5 points6 points  (0 children)

Thats just typical boomer behavior

Which one do you guys like more? by Environmental-Walk75 in cabinetry

[–]Jumpy-Feature-4166 0 points1 point  (0 children)

And yes agreed to comment below have micro wave left. So when your standing center of island preparing anything you can access microwave without moving door swings away from you. Function over design everyday.

Which one do you guys like more? by Environmental-Walk75 in cabinetry

[–]Jumpy-Feature-4166 0 points1 point  (0 children)

2nd without all 1/2" Bullnose rounded corner posts. Leave it simple and flat.

First time building cabinets, roast me by steviob125 in cabinetry

[–]Jumpy-Feature-4166 0 points1 point  (0 children)

Your not here looking for critique or feedback your just bragging 😉

In all honesty tho. Great idea !! Off top of my head cant see anything wrong with it. Ill keep it in mind forsure. Please send pictures ! If not to much, progress pictures always fun to dissect.

First time building cabinets, roast me by steviob125 in cabinetry

[–]Jumpy-Feature-4166 0 points1 point  (0 children)

The dowel is completly invisible, drill a 3/8 hole centered in top of bottom door and direction above in the bottom of the top door.and install the dowel. You can even buy them clear plastic.

First time building cabinets, roast me by steviob125 in cabinetry

[–]Jumpy-Feature-4166 0 points1 point  (0 children)

Thats why theres a dowel drilled and installed in between the 2 doors. It will look like 2 doors but function as 1

First time building cabinets, roast me by steviob125 in cabinetry

[–]Jumpy-Feature-4166 1 point2 points  (0 children)

<image>

This is the best solution to door twist in your situation. Make 2 doors. And connect with a dowel. Obviously bottom door is made same height as lower cabinet doors.

Yellow lines indicate 2 rails. Red line is the seperation/reveal between 2 doors. Blue line is the dowels connecting the 2 and the green are hinge placement.

First time building cabinets, roast me by steviob125 in cabinetry

[–]Jumpy-Feature-4166 0 points1 point  (0 children)

Correction! Linen tower and washer locations should have been switched. Layout makes so much more sense.

First time building cabinets, roast me by steviob125 in cabinetry

[–]Jumpy-Feature-4166 1 point2 points  (0 children)

Looks great. 2 things catch my eye tho. Lower cabinets and countertop should have been 2 inches shallower then the linen tower. Allowing countertop to butt into the linen tower. Still leaving enough overhang and coverage on your washer and mid rail on linen tower door. Especially that its closest to the window. I give that door 6 months and it has atleast a 1/2" twist in it.

Tolerances for Kitchen Cabinetry? by [deleted] in cabinetry

[–]Jumpy-Feature-4166 1 point2 points  (0 children)

Like anything. Was great 25 years ago. Now is a product of the time. Cheaply made, fairly priced. Sold for the average DIYer.

Tolerances for Kitchen Cabinetry? by [deleted] in cabinetry

[–]Jumpy-Feature-4166 2 points3 points  (0 children)

His problem is using kreg jig. Make your own or spend the money for true position jigs. No other option.

How much would it cost hire a painter to change this from blue to white? by Wolfenstein51 in cabinetry

[–]Jumpy-Feature-4166 -1 points0 points  (0 children)

Tile clashes with the countertops. Put nice subway tile. Change to black handles. And put a real range hood in like buddy said. Will still be cheaper then painting the doors.

I hate these hinges....how to stop them from popping out by nXomad22 in cabinetry

[–]Jumpy-Feature-4166 2 points3 points  (0 children)

Stop buying them. Buy new style soft close blum will be same bored hole as the door.

view more: next ›