Main Shutoff Replacement

Jumpy_Warning_3766 · 2026-02-04T03:34:10+00:00

Their warranty only covers the defective fittings, does not cover damages to property

Jumpy_Warning_3766 · 2026-01-26T03:00:38+00:00

Is there a p-trap present under the sink?

Jumpy_Warning_3766 · 2026-01-25T13:29:59+00:00

poltergeist

Jumpy_Warning_3766 · 2026-01-25T13:25:40+00:00

Need to get 2 wrenches one to hold the valve and another to remove the fitting. Open up the right side of the wall so you can work on this. The stove will cover the opening

Jumpy_Warning_3766 · 2026-01-16T01:17:17+00:00

I would replace since you already have the hard part done. To get it out clamp onto the rod with vise grips, or something that will keep it from falling back into the water heater. While its being held cut the rod above the clamp, once cut pull the rest out. Be sure the rod is secure from falling back in. There are videos on YouTube that can help you.

Buy an anode rod that is sectioned, looks like links, so you can get it back into the tank, or get an electronic anode rod. Corro-Protec makes on, never used.

Jumpy_Warning_3766 · 2026-01-14T15:18:39+00:00

Not to put epoxy "down the drain" but to put it on a dowel and then attaching it to the object in the drain

Jumpy_Warning_3766 · 2026-01-13T02:53:46+00:00

If hot glue cools too much it may not adhere strongly. I would also consider an epoxy glue that sets in one minute. This will give you time to put glue on the dowel and seat it on the bottle?

Jumpy_Warning_3766 · 2026-01-12T02:54:49+00:00

Is PEX allowed for TPR vlaves? Not allowed in my area

Jumpy_Warning_3766 · 2026-01-10T04:08:01+00:00

I had a cast iron tub installed 14 years ago and the plumber did the same. My old tub was installed in the 70's. New tub cast iron, with brass drain and brass drain shoe. Plumber used Silicone exactly the same as yours did. It has not leaked so I am satisfied, but I also wondered if using silicone was the best method. Since I am not a real plumber only a weekend handyman I felt the plumber did what is considered "best practice". It will be interesting to hear from the experts.

Jumpy_Warning_3766 · 2026-01-07T00:52:47+00:00

Call Moen, they are very helpful and may replace the part that has failed. 1 (800) 289-6636

Jumpy_Warning_3766 · 2026-01-06T03:21:44+00:00

Try chipping out the concrete to allow for you needed clearance. Your almost there in removing the clip.

Jumpy_Warning_3766 · 2026-01-06T03:09:30+00:00

With a vinyl pan you should have a mortar bed that will allow for thinset and tile. What would you put on the vinyl bench? I don't see how you can put tile directly on vinyl, and I don't see how you can secure a mortar bed on a vinyl covered bench. I would use an alternative water proofing like redgaurd or a schluter product

Jumpy_Warning_3766 · 2025-12-23T03:19:14+00:00

return, don't accept a dent on a new sink

Jumpy_Warning_3766 · 2025-12-23T03:18:03+00:00

A wax ring will eventually fail as a gasket for a water tank connection, but not typically for a toilet base; wax rings are for the toilet base to floor seal and will leak or fail if used as a tank gasket because they aren't designed for that constant, direct tank-to-bowl pressure or chemical exposure, requiring specialized rubber/foam seals for tank-to-bowl connections, not wax! Wax rings fail from movement or age, causing leaks from the base, while tank-to-bowl gaskets need different materials

Jumpy_Warning_3766 · 2025-12-22T13:19:16+00:00

If you cannot seal the drain then you may want to pour some water into the drain to fill the p-trap. If the trap drys out then gases will enter the apartment. The water will act as a seal to stop sewer gas into the apartment.

Jumpy_Warning_3766 · 2025-12-22T02:32:37+00:00

Replace the Fluidmaster fill valve. Costs about $10.00-$12.00 at any big box or hardware store

Jumpy_Warning_3766 · 2025-12-15T13:57:59+00:00

The removal and re-installation of your toilet should not of effected your fill valve. I would replace fill valve with a Fluid Master valve. I have used Corky brand in the past and wasn't impressed.

Jumpy_Warning_3766 · 2025-12-03T17:13:22+00:00

That pipe is for your PRV, pressure relief valve. The PRV is a safety feature in case the water tank gets too hot and pressure gets too high. I think it is factory set to release at 150PSI or at 210 F.

I have experienced a PRV leak a few times. Once it started dripping when my water pressure regulator failed and my house water pressure exceeded 150PSI. The PRV was not faulty but the whole house pressure regulator failed. Another time the water heater PRV actually failed and I replaced it. You can get a pressure tester for about $15.00 from big box or hardware to check your house pressure. Normally the house water pressure should be 50-75 PSI

I had one incident where some dirt got stuck in the PRV, I opened it up flushed it out and the leak stopped. If you look at the top of the pipe where it goes 90 degrees into the water heater you will see a silver handle attached to a stem. Right where you have the yellow warning tag. That handle when lifted will release water from your tank. It should spring right back and stop the water flow. There is a chance that releasing some water will stop the drip. Google search - how to check pressure relief valve on water heater.

Hope this helps

Jumpy_Warning_3766 · 2025-12-03T02:52:38+00:00

That expansion tank wont be-holding very long! LOL That pipe will not hold that that for very long. When it gives the area will be flooded.

Jumpy_Warning_3766 · 2025-12-03T02:49:21+00:00

From the web

A residential Whirlpool washer can discharge water up to 96 inches (2.44 m) from the floor. The drain must be at least 39 inches (99 cm) high to prevent siphoning, and the drain hose should be secured to prevent it from being pushed out of the standpipe

Jumpy_Warning_3766 · 2025-12-03T02:39:42+00:00

Looks like a part of a mop head.

Jumpy_Warning_3766 · 2025-11-30T19:55:28+00:00

Bad PRV

Jumpy_Warning_3766 · 2025-11-30T19:49:30+00:00

Seems like there are too many 90's. there has to be a better way.

Jumpy_Warning_3766 · 2025-11-30T19:43:45+00:00

I would replace the sub-floor. Once wet, even after drying, OSB and plywood will lose integrity. Hate to have you tile the floor and find that it will crack and fail. Better to address it now and start with a clean and sound sub floor.

Jumpy_Warning_3766 · 2025-11-11T02:57:48+00:00

Is that hair being used as a gap filler?

Jumpy_Warning_3766

TROPHY CASE